manualshive.com logo in svg

KidKraft Cedar Summit F29080, Installation And Operating Instructions Manual

Share
Download
KidKraft Cedar Summit F29080 Installation And Operating Instructions Manual Download Page 21

 21 

 

  

1 x 

Left Access 1 3/8 x 2 1/2 x 57 53/64”

1 x 

Right Access 1 3/8 x 2 1/2 x 57 53/64”

4 x 

Tread 15/16 x 3 1/4 x 16 3/16”

9545

9055

9054

Fig. 2.1

Fig. 2.3

Wood Parts

Hardware

Step 2:  Access Ladder/Rope Wall Assembly 

Part 1

16 x 

#8 x 2-1/2” Wood Screw

S3

Fig. 2.2

End View

Flush to edges

Top Edge of Access Rail

S3

9054

9545

AI-1

S3 X16

AI-1

S3 X16

AI-1

S3 X16

9055

9545

S3

S3

A:

 Place (9054) Left Access on one side of 4 (9545) Treads and (9055) Right Access on the other side with the 

grooves facing in. (fig. 2.1)

B:

 Fit each (9545) Tread into grooves on both (9054) and (9055) Access rails, make sure the top edge of the 

(9545) Treads are flush to the front of the Access rails. (fig. 2.1 and 2.2)

C:

 Pre-drill pilot holes with a 1/8” drill bit and attach rails and treads together using 4 (S3) #8 x 2-1/2” Wood 

Screws per tread. (fig. 2.1, 2.3)

Summary of Contents for Cedar Summit F29080





















































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands