KidKraft Cedar Summit F29080 Installation And Operating Instructions Manual Download

Page: 79 / 116

AI-44

S20 X11

11 x

#8 x 1-3/8” Wood Screw

Hardware

S20

1 x

Roof Base 5/8 x 4 x 40”

1 x

Narrow Roof base 5/8 x 1 1/4 x 35 11/16”

1 x

Roof Base Narrow 5/8 x 2 3/4 x 40”

Wood Parts

9549

9550

9554

S20

9554

9549

9550

Fig. 30.1

Note hole

orientation

Note hole

orientation

Flush

Step 30: Attach Soffits

Taking care to note the hole orientation, place 1 (9549) Roof Base along the top of the front wall panel so that

it’s flush with the inside of the wall. Attach using 4 (S20) #8 x 1- 3/8” Wood Screws. (fig. 30.1)

Place (9550) Narrow Roof Base along the end panel making sure that it’s flush to (9549) Roof Base. Attach

using 3 (S20) #8 x 1- 3/8” Wood Screws. (fig. 30.1)

Place (9554) Roof Base Narrow over the back wall panel so that it’s flush to the inside edge of the wall and to

(9550) Narrow Roof Base. Attach with 4 (S20) #8 x 1- 3/8” Wood Screws. (fig. 30.1)

Summary of Contents for Cedar Summit F29080





















































































































Search results

Summary of Contents for Cedar Summit F29080

Reviews:

Related manuals for Cedar Summit F29080

Brands by name

Popular brands

KidKraft Cedar Summit F29080, Installation And Operating Instructions Manual

Search results

Summary of Contents for Cedar Summit F29080

Reviews:

Related manuals for Cedar Summit F29080

Brands by name

Popular brands