KidKraft Cedar Summit F29080 Installation And Operating Instructions Manual Download Page 65

Page: 65 / 116

WB2 X4(FW2 LW2 TN2)
H2 X10(FW1 LW1 TN1)

Hardware

4 x

5/16 x 1-3/8” Wafer Head Bolt

(5/16” flat washer, 5/16” lock washer, 5/16” t-nut)
10 x ¼ x 2” Hex Bolts (with flat

washer, lock washer and t-nut)

WB2

1/4”

T-Nut

1/4”

T-Nut

5/16” Flat

Washer

5/16” Flat

Washer

5/16” Flat

Washer

5/16” Flat

Washer

5/16”

T-Nut

5/16”

T-Nut

5/16”

T-Nut

5/16”

T-Nut

WB2

(hidden)

9556

9555

9566

9555

9566

9557

Wood Parts

1 x

Fence Post 1 1/4 x 3 x 33”

2 x

Bottom Fence 1 1/4 x 3 x 37 9/16”

5 x

Fence Board 5/8 X 3 X 33”

1 x

Fence Post A 1 1/4 x 3 x 33”

9556

9555

9566

9557

1/4” Flat

Washer

1/4” Lock

Washer

Fig. 24.3

Place 2 (9555) Bottom Fence boards one above the other with the notched out ends facing up. Fit 1 (9557)

Fence Post A into the notches on the right side of the (9558) Fence Bottom Narrows 1 (9556) Fence Post on the

left side and attach using 2 (WB2) 5/16 x 1- 3/8” Wafer Head Bolts (with flat washer, lock washer and t-nut) per

board.

Flip the assembly over and install 5 (9566) Fence Boards into the pre-drilled holes using 2 (H2) 1/4 x 2” Hex

Bolts (with flat washer, lock washer and t-nut) per board. (fig. 24.3)

Step 24: Attach Fence Assembly

Part 3

5/16” Lock

Washer

5/16” Lock

Washer

5/16” Lock

Washer

5/16” Lock

Washer

Summary of Contents for Cedar Summit F29080





















































































































Search results

Summary of Contents for Cedar Summit F29080

Reviews:

Brands by name

Popular brands

KidKraft Cedar Summit F29080, Installation And Operating Instructions Manual

Search results

Summary of Contents for Cedar Summit F29080

Reviews:

Brands by name

Popular brands