KidKraft Cedar Summit F29080 Installation And Operating Instructions Manual Download

Page: 92 / 116

Step 40: Attach Elbow Assembly to Flange Assembly

Other Parts

1 x Quadrex Driver

24 x 1/4 x 12.7mm Pan Bolt

24 x 1/4” Square Lock Nut

Fig. 40.3

Align each elbow using the

molded arrows.

Fig. 40.2

Top Slide Bolt Holes

Elbow

Assembly

Quadrex Driver

Use special driver provided

in locations where the curve

of the elbow are difficult to

reach with a standard driver.

Note: Keep all bolts loose until further step.

Fit one of the Elbow Assemblies to the Flange Assembly by lining up the arrows on each assembly. Attach

Elbow Assembly to Flange Assembly using 6 (PB1) ¼ x 3/4” Pan Bolts and Square Lock Nut. (fig. 40.1, 40.2 and

40.3)

Attach one of the Elbow assemblies to another Elbow Assembly making sure to line up the arrows on each

assembly. Attach 6 (¼ x 12.7)mm Pan Bolt with Square Lock Nut. Repeat this instruction for 2 more. (fig. 40.2

and 40.3)

Use Quadrex Driver as a guide pin for each hole before inserting bolt.

Flange

Assembly

Square

Lock Nut

¼ x 12.7mm

Pan Bolt

Use a 7/16” open end

wrench for nuts

Fig. 40.1

AI-55

Summary of Contents for Cedar Summit F29080





















































































































Search results

Summary of Contents for Cedar Summit F29080

Reviews:

Related manuals for Cedar Summit F29080

Brands by name

Popular brands

KidKraft Cedar Summit F29080, Installation And Operating Instructions Manual

Search results

Summary of Contents for Cedar Summit F29080

Reviews:

Related manuals for Cedar Summit F29080

Brands by name

Popular brands