KidKraft Cedar Summit F29080 Installation And Operating Instructions Manual Download

Page: 43 / 116

Fig. 13.10

Hardware

Wood Parts

Fig. 13.9

Fig. 13.8

1 x

Door Stop 1 x 2 1/2 x 10”

2715

2 x

#7 x 1-1/8” Pan Screw

3 x

#8 x 2” Wood Screw

S38

S11

Other Parts

1 x Magnetic Catch

Inside View

Side View

S38

2715

Magnetic Catch

Catch Plate

2715

1-1/4”

9286

Step 13: Door Panel Assembly

Part 4

S11

In the notched out opening of (2715) Door Stop attach the Magnetic Catch using 2 (S38) #7 x 1-1/8” Pan

Screws. (fig. 13.8)

Important: Use a hand held screw driver and DO NOT over tighten.
G:

On the inside of the assembly, attach (2715) Door Stop to (9286) Front Panel Assembly with 3 (S11) #8 x 2”

Wood Screws, making sure (2715) Door Stop overhangs (9286) Front Panel Assembly by 1-1/4” and is in position

to receive the Catch Plate.

AI-20

S38 X2

S11 X3

Summary of Contents for Cedar Summit F29080





















































































































Search results

Summary of Contents for Cedar Summit F29080

Reviews:

Related manuals for Cedar Summit F29080

Brands by name

Popular brands

KidKraft Cedar Summit F29080, Installation And Operating Instructions Manual

Search results

Summary of Contents for Cedar Summit F29080

Reviews:

Related manuals for Cedar Summit F29080

Brands by name

Popular brands