KidKraft Cedar Summit F29080 Page 96 Installation And Operating Instructions Manual Download

Page: 96 / 116

AI-57

On the fourth attached Elbow Assembly remove the pan bolt and nut which is facing the fort (installed in Step 38).

(fig. 44.1) The bolt will no longer be needed, but keep the lock nut.

Loosely attach TNR3 Tube Support (at the slightly bent end) to the slide seam using 1 (PB6) 1/4 x 1” Pan Bolt (with

flat washer and the previously removed lock nut). (fig. 44.2)

Rotate TNR3 Tube Support and attach to Slide End Panel using 1 (S6) #12 x 1” Pan Screw as shown in (fig. 44.2).

Fully tighten screw and bolt.

Hardware

1 x

#12 x 1” Pan Screw

1 x

1/4 x 1” Pan Bolt

(1/4” flat washer & 1/4” lock nut - previously removed)

PB6

Other Parts

1 x TNR3 Tube Support

Step 44: Attach TNR 3 Slide to Fort

Remove PB1 (1/4 x 3/4”

Pan Bolt) first then install

PB6 (1/4 x 1” Pan Bolt

with flat washer)

Fig. 44.2

Fig. 44.1

Slide End Panel

Lock

Nut

PB6

Slide End

Panel

Flat

Washer

AI-57

TNR 3 Tube

Support

Note: Flat

end down

Summary of Contents for Cedar Summit F29080





















































































































Search results

Summary of Contents for Cedar Summit F29080

Reviews:

Related manuals for Cedar Summit F29080

Brands by name

Popular brands

KidKraft Cedar Summit F29080, Installation And Operating Instructions Manual

Search results

Summary of Contents for Cedar Summit F29080

Reviews:

Related manuals for Cedar Summit F29080

Brands by name

Popular brands