KidKraft Cedar Summit F29080 Page 68 Installation And Operating Instructions Manual Download

Page: 68 / 116

S11 X4

AI-35

S3 X12

S11 X4

AI-35

S3 X12

1 x

Nest Right Access 1 3/8 x 2 1/2 x 39 13/16”

1 x

Nest Left Access 13/8 x 2 1/2 x 39 13/16

3 x

Nest Tread 15/16 x 3 1/4 x 13 1/2”

1 x

Stop 5/8 x 3 x 14 3/4”

Step 26: Nest Ladder Assembly

Part 1

Wood Parts

Hardware

9569

9572

9571

9570

12 x

#8 x 2-1/2” Wood Screw

4 x

#8 x 2” Wood Screw

S11

Fig. 26.1

Fig. 26.3

9571

9572

9571

9569

9570

x 6 per

side

x 4

Flush to

top edge

S11

2-3/8” gap between top

Tread and Ladder Gap

Place (9570) Nest Left Access on one side of 3 (9571) Nest Treads and (9569) Nest Right Access on the other

side with the grooves facing in. (fig. 26.1 & 26.2)

Fit each (9571) Nest Tread into grooves on both ( 9569) and (9570) Nest Access Rails, making sure the top

edge of the ( 9571) Nest Treads are flush to the front of the Access rails. (fig. 26.1 & 26.2)

Pre-drill pilot holes with a 1/8” drill bit and attach rails and treads together using 4 (S3) #8 x 2-1/2” Wood

Screws per tread. (fig. 26.1 & 26.2)

Place (9572) Stop Behind on each access rail so there is a 2-3/8” gap between (9572) Stop Behind and the top

(9571) Nest Tread. Attach using 4 (S11) #8 x 2” Wood Screws. (fig. 26.1 & 26.3)

Fig. 26.2

9571

End View

Flush to

edges

Top Edge of

Access Rail

Summary of Contents for Cedar Summit F29080





















































































































Search results

Summary of Contents for Cedar Summit F29080

Reviews:

Related manuals for Cedar Summit F29080

Brands by name

Popular brands

KidKraft Cedar Summit F29080, Installation And Operating Instructions Manual

Search results

Summary of Contents for Cedar Summit F29080

Reviews:

Related manuals for Cedar Summit F29080

Brands by name

Popular brands