KidKraft Cedar Summit F29080 Installation And Operating Instructions Manual Download

Page: 72 / 116

AI-38

S11 X16

x 8 per

side

(hidden)

9552

9276

9277

9551

9552

9551

1 x

Back Roof 1 1/4 x 38 1/4 x 40 13/16”

1 x

Front Roof 1 1/4 X 38 1/4 X 40 13/16”

Hardware

16 x

#8 x 2” Wood Screw

S11

Wood Parts

9276

9277

Fig. 27.2

Flush

S11

Step 27: Roof Assembly

Part 2

With a helper, hold (9276) Back Roof and (9277) Front Roof in position so that they are flush at the roof peak

and line up with the roof support assemblies.

Making sure that the roof support assemblies are flush to the bottom of the roof panels, attach each roof

support assembly to each end of the roof panels using 8 (S11) #8 x 2” Wood Screws per end. (fig. 27.2)

Summary of Contents for Cedar Summit F29080





















































































































Search results

Summary of Contents for Cedar Summit F29080

Reviews:

Related manuals for Cedar Summit F29080

Brands by name

Popular brands

KidKraft Cedar Summit F29080, Installation And Operating Instructions Manual

Search results

Summary of Contents for Cedar Summit F29080

Reviews:

Related manuals for Cedar Summit F29080

Brands by name

Popular brands