KidKraft Cedar Summit F29080 Installation And Operating Instructions Manual Download

Page: 60 / 116

AI-30

WB8 X5(FW2 TN2)

S11 X1

S4 X4

S3 X4

AI-30

WB8 X5(FW2 TN2)

S11 X1

S4 X4

S3 X4

AI-30

WB8 X5(FW2 TN2)

S11 X1

S4 X4

S3 X4

9287

9560

9561

9562

S11

5 x

5/16 x 2-3/8” Wafer Bolt

(5/16” flat washer, 5/16” t-nut)

WB8

Hardware

Wood Parts

1 x

Terrace support left 1 x 2 3/8 x 47 3/4”

1 x

Terrace support Right 1 x 2 3/8 x 47 3/4”

1 x

Mid Joist 1 x 2 3/8 x 33 11/16”

9560

9561

9562

4 x

#8 x 2-1/2” Wood Screw

1 x

#8 x 2” Wood Screw

S11

WB8

5/16” Flat

Washer

5/16”

T-Nut

9286

9561

Fig. 23.2

Fig. 23.3

5/8”

Place (9561) Terrace Support Right and (9560) Terrace Support Left on either side of (9562) Mid Joist, taking

note of the hole orientation. Line (9562) Mid Joist up with the pre-drilled holes in each Terrace Support and attach

using 2 (S3) #8 x 2 -1/2” Wood Screws per side. (Fig. 23.1 & 23.2)

From inside the assembly measure 5/8” (15.9mm) down from the top of the Wall Panels and place the Terrace

Support Assembly so that the (9560) Terrace Support Left and (9561) Terrace Support Right are tight to the (9553)

Supports. (Fig. 23.1 & 23.3)

From inside, loosely install 2 (WB8) 5/16 x 2 -3/8” Wafer Bolts (with flat washer and t-nut) into (9560) Terrace

Support Left and 3 (WB8) 5/16 x 2 -3/8” Wafer Bolts (with flat washer and t-nut) into (9561) Terrace Support Right.

Check to make sure the Terrace Support Assembly is level, then tighten the Wafer Bolts. (Fig. 23.1 & 23.3)

Install 1 (S11) #8 x 2” Wood Screw into the end of (9560) Terrace Support Left as shown in fig. 23.1

Step 23: Attach Terrace Assembly

Part 1

Fig. 23.1

Summary of Contents for Cedar Summit F29080





















































































































Search results

Summary of Contents for Cedar Summit F29080

Reviews:

Related manuals for Cedar Summit F29080

Brands by name

Popular brands

KidKraft Cedar Summit F29080, Installation And Operating Instructions Manual

Search results

Summary of Contents for Cedar Summit F29080

Reviews:

Related manuals for Cedar Summit F29080

Brands by name

Popular brands