KidKraft Cedar Summit F29080 Installation And Operating Instructions Manual Download

Page: 41 / 116

AI-18

S37 X8

S38 X2

S37 X2

AI-18

S37 X8

S38 X2

S37 X2

Fig. 13.4

Fig. 13.3

Fig. 13.5

Hardware

8 x

#7 x 5/8” Pan Screw

S37

Other Parts

1 x Door Handle
2 x Door Hinge

Top View

Door

Handle

Door

Hinge

Door

Hinge

Door

Hinge

S37

x 3 per hinge

2837

Outside View

1/2”

Hinge

Step 13: Door Panel Assembly

Part 2

On the outside of the (2837) Door Window Panel attach the second Door Handle at approximately the same

place as the one on the inside. Use 2 (S37) #7 x 5/8” Pan Screws. (fig. 13.3)

Attach 2 Door Hinges on the outside of the (2837) Door Window Panel on the opposite side from the Door

Handle. Judge spacing based on fig. 13.3. Use 3 (S37) #7 x 5/8” Pan Screws per Hinge.

Note:

Hinge stops must be tight to (2837) Door Window Panel. (fig. 13.4)

Summary of Contents for Cedar Summit F29080





















































































































Search results

Summary of Contents for Cedar Summit F29080

Reviews:

Related manuals for Cedar Summit F29080

Brands by name

Popular brands

KidKraft Cedar Summit F29080, Installation And Operating Instructions Manual

Search results

Summary of Contents for Cedar Summit F29080

Reviews:

Related manuals for Cedar Summit F29080

Brands by name

Popular brands