KidKraft Cedar Summit F29080 Page 50 Installation And Operating Instructions Manual Download

Page: 50 / 116

Hardware

12 x

5/16 x 6-1/8” Hex Bolt

(5/16” flat washer x 2, 5/16” lock nut & plastic formed washer)

1 x

5/16 x 3” Wafer Bolt

(5/16” flat washer, 5/16” t-nut)

4 x

#7 x 1-1/8” Pan Screw

Other Parts

6 x Heavy Duty Swing Hangers
6 x Spring Loaded Quick Link
1 x Cedar Summit by KidKraft

Plaque

Wood Parts

1 x Engineered SW Beam 3 x 5 1/4 x 92”

Step 17: Swing Beam Assembly

Part 1

Attach 6 Heavy Duty Swing Hangers to (9049) Engineered SW Beam using 2 (G13) 5/16 x 6-1/8” Hex Bolt

(with 2 flat washers, plastic formed washer and lock nut) per swing hanger, as shown in fig. 17.1 and 17.2.

Attach 1 Spring Loaded Quick Link to each Heavy Duty Swing Hanger. (fig. 17.3)

Install 1 (WB7) 5/16 x 3” Wafer Bolt (with flat washer and t-nut) in the middle bolt hole, from the bottom

up, in (171) Engineered SW Beam as shown in fig. 17.1 and 17.4.

IT IS IMPORTANT THAT THIS BOLT IS

ATTACHED. IT WILL MINIMIZE CHECKING OF WOOD.

Attach Cedar Summit by KidKraft Plaque to centre of (9049) Engineered SW Beam (over top of t-nut) using

4 (S38) #7 x 1-1/8” Pan Screws. (fig. 17.5)

9049

Fig. 17.3

9049

Fig. 17.1

Fig. 17.2

Fig. 17.5

5/16” Flat

Washer

Heavy Duty

Swing Hanger x 6

5/16” Flat

Washer

5/16”

T-Nut

Swing End

Fort End

S38

x 4

5/16”

Lock Nut

Cedar Summit

Plaque

9049

5/16” Flat

Washer

Plastic

Formed

Washer

Heavy Duty

Swing Hanger

Heavy Duty

Swing Hanger

G13

WB7

Spring

Loaded

Quick Link

9049

Fig. 17.4

WB7

Caution: The Spring Loaded Quick Link

must be attached to the Heavy Duty Swing

Hanger in the closed position. (fig. 17.4)

Spring Loaded Quick

Link in the closed

position

S38

Summary of Contents for Cedar Summit F29080





















































































































Search results

Summary of Contents for Cedar Summit F29080

Reviews:

Related manuals for Cedar Summit F29080

Brands by name

Popular brands

KidKraft Cedar Summit F29080, Installation And Operating Instructions Manual

Search results

Summary of Contents for Cedar Summit F29080

Reviews:

Related manuals for Cedar Summit F29080

Brands by name

Popular brands