manualshive.com logo in svg

KidKraft Cedar Summit F29080, Installation And Operating Instructions Manual

Share
Download
KidKraft Cedar Summit F29080 Installation And Operating Instructions Manual Download Page 44

 44 

 

  

4 x 

#12 x 2” Pan Screw

2 x 

#8 x 2-1/2” Wood Screw

1 x 

Table Top 15/16 x 4 1/4 x 42 4/5”

1 x 

Table Support  1 1/4 x 1 1/4 x 39 5/8”

Wood Parts

2611

9539

Hardware

S7

S3

Step 14:  Front Wall Assembly 

Part 1

A: 

Place (9539) Table Support flush to the notched of (2611) Table Top and attach with 4 (S7) #12 x 2” Pan 

Screws as shown in fig. 14.1.

B:

 Place Table Top Assembly in the center of opening and tight to (9286) Front Panel Assembly and attach (9539) 

Table Support to (9286) Front Panel Assembly with 2 (S3) #8 x 2-1/2” Wood Screws. (fig. 14.2 and 14.3) 

S37 X6

AI-21

S7 X4

S3 X2

S3

S7

2611

9286

Flush

9539

Fig. 14.1

Fig. 14.2

S37 X6

AI-21

S7 X4

S3 X2

S3

9539

2611

x 2 per   

side

Tight

Fig. 14.3

Summary of Contents for Cedar Summit F29080





















































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands