KEPCO BOP-ME 1KW, Operator'S Manual

Page: 84 / 234

3-8
BOP HIPWR 091719
Power-up Screen (Power up menu)
•
!
- Save/Recall
• • Saved Setups (Figure 3-10): Recall one of 99 saved setups.
• • • Saved Setup Details (Table 3-9): Mode (voltage/current/External), main channel reference (inter-
nal/external/external reference level) and setting, Protection Type (internal/external/LesserLimit) and
setting(s), output status (on/off)
•
@
- Waveform
• • Saved Waveforms (Figure 3-11): Choose one of 16 saved waveforms.
• • • New Waveform Settings (Table 3-13): Name (max. 10 characters), mode (voltage/current) No. of cycles,
+Protect, -Protect)
• • • • First segment: type (Square/ +ramp /-ramp/triangle/sine/level), Frequency, PtoP Amplitude, Offset
• • • Edit Waveform (Figure 3-12): Name, no. of cycles, +protect, -protect, segment list, mode
• • • • Segment Details (Table 3-12): Type ((ramp/-ramp/triangle/sine/level/slope/trigger),
frequency or period, amplitude, offset, start/stop angle for sine and triangle, Repeat (initial/repeat)
•
#
- Display
• • Display Settings (Table 3-3): Graphic Display ( meters /graphics, background ( black /white/mono-
black/blue/green/lt.green/ lt.blue), Protect Entry ( independent /bipolar) Waveform Stop ( outputOFF /User
Option), Key Press beep ( On /Off/Error only)
•
$
- Analog Remote Setup (Table 3-16):
• • Analog Remote Settings: Reference input ( internal /external/external reference level), protect limit ( Inter-
nal /External/LesserLimit), external mode ( disable/ enable)
•
%
- General Setup
• • Interface Settings (Table 3-17):
• • • *RST set Output ( on /off),
• • • GPIB Settings (Table 3-17): Language ( SCPI /CIIL), GPIB address (default = 6 ), Device clear
( SCPI /MATE)
• • • Serial Settings (Table 3-17): Baudrate ( Off /9600/19200/38400), Xon/Xoff ( disable /enable), prompt ( dis-
abled/echo/ enabled/enab+echo)
• • • LAN Setting (Table 3-18): IP Address, IP MASK, AUTO IP ON , DHCP ON , Name and index (MDNS
name)
• • Max/Min Settings (Table 3-5): for voltage mode: +Voltage max, –Voltage min, ±CProtect max/min; for cur-
rent mode: +Current max, –Current min, ±VProtect max/min
• • Load Type (Figure 3-8): Active /Resistive/Battery, Remote On-off: (disabled/high is off/low is off/high is
on/low is on/LowPulseOff)
• • Remote On/Off (Shutdown or Output On/Off) Operation (Table 2-3): LowPulse , HighIsOn, LowIsOn, HighI-
sOff, LowIsOff, Disabled
• • Revisions/Test: (Tests: display, keypad, LAN, interface, serial, analog and output)
• • Calibration (PAR. 4.4): Voltage, Current and External and Controls calibration. Shows Firmware versions
for Display, Serial, GPIB, LAN and analog.
• • Power-up Settings (PAR. 3.3.8): Mode ( Voltage /Current/External), Main channel Reference ( Inter-
nal /External/ExtlRefLev), main setting, Protection: Type ( Internal /External/LesserLimit), Voltage Limit (cur-
rent mode), Current Level (voltage mode), output ON /OFF
• • Password (See Figure 3-6 for default settings)
• • • Password Settings: Menu protection (Interface/Max-Min/Load/Test/Calibration/Power-up/Keypad @
local/Keypad@power-up), Save Display Change (Enable/
Disable ), Passwords (Unpro-
tected/Main/Admin1/Admin2)
• • • Series/Parallel (Table 2-12): Configuration (Standalone/Parallel/Series/Master 2X2/Master 3X2); for
parallel or series: Unit Type (Standalone/1 to+4/Slave #1 to #4) and Configuration: shows
Series or Parallel).
3.2.4.1 HOW TO MODIFY A PARAMETER
First access the parameter by accessing the proper menu as described above (PAR 3.2.4);
Tables 3-3 through 3-16 list the menu parameters. To modify a parameter listed in a menu or
submenu, proceed as follows:
1. Highlight the parameter using the
Y
and
U
keys.
2. When the desired choice is highlighted, press
!
to modify the active setting. The choices
are displayed with the active setting highlighted. In the case of numerals, the units digit is
highlighted.