B-22
BOP-1K 091719
B.73
[SOURce:]LIST:DWELl? QUERY
LIST:DWEL?
Syntax:
Short Form: LIST:DWEL?
Long Form: LIST:DWELl?
Return Value: <value>
Description:
Identifies the dwell times entered for the list.
Starting at location established by LIST:QUERy,
returns comma-separated list of up to 16 values indicating the dwell time parameters entered. i.e., the
contents of LIST:DWEL locations of Table B-3. Related Commands: LIST: DWEL, LIST:QUERy. (See
example, Figure B-6.)
B.74
[SOURce:]LIST:DWELl:POINts? QUERY
LIST:DWEL:POIN?
Syntax:
Short Form: LIST:DWEL:POIN?
Long Form: LIST:DWELl:POINts?
Return Value: <value> (0 to 5900)
Description:
Identifies the number of locations for which time values have been entered and the next loca-
tion to be filled by a LIST:DWEL command.
If LIST:DWEL:POIN? returns 6, dwell times have been
entered for locations 0 through 5 and location 6 is the next to be filled by a LIST:DWEL command.
LIST:DWEL, LIST:DWEL:POIN. (See example, Figure B-6.)
B.75
[SOURce:]LIST:ERASe COMMAND
LIST:ERAS
Syntax:
Short Form: LIST:ERAS <int_value>
Long Form: LIST:ERASe <int_value>
int_value = <n> where n = waveform location (from 1 to 16) to be erased
Description:
Used to erase one of 16 stored waveforms.
B.76
[SOURce:]LIST:QUERy COMMAND
LIST:QUER
Syntax:
Short Form: LIST:QUER <int_value>
Long Form: LIST:QUERy <int_value>
int_value = <n> where n = first location to be queried.
Description:
Determines first location to be queried by LIST:VOLT?, LIST:CURR? or LIST:DWEL? queries.
Related Commands: LIST:VOLT?, LIST:CURR?, LIST:DWEL?. LIST:QUER?. (See example, Figure B-6.)
B.77
[SOURce:]LIST:QUERy? QUERY
LIST:QUER?
Syntax:
Short Form: LIST:QUER?
Long Form: LIST:QUERy?
Return Value: <int_value>
Description:
Identifies first location to be queried by LIST:VOLT?, LIST:CURR?, LIST:DWEL? queries.
Related Commands: LIST:QUER, LIST:CURR?, LIST:DWEL?. LIST:QUER?. (See example, Figure B-6.)
B.78
[SOURce:]LIST:RECall COMMAND
LIST:REC
Syntax:
Short Form: LIST:REC <n>
Long Form: LIST:RECall <n>
where:
<n> = number from 1 to 16 representing location where waveforms are stored.
Description:
Recalls the waveform previously saved in location specified by <n>.
This command must be pre-
ceded by LIST:CLE, otherwise a “lists not same length” error is generated. If the location specified is
empty, a “name not found” error is generated.
B.79
[SOURce:]LIST:REPeat COMMAND
LIST:REP
Syntax:
Short Form: LIST:REP <int_value1>,<int_value2>,<array>
Long Form: LIST:REPeat <int_value1>,<int_value2>,<array>
where
<int_value1> is start point to be copied
<int_value2> is end point to be copied
<array> is a series of comma separated values representing the new
programmed current (Amps) for current list, or programmed voltage (Volts) for voltage list.
Description:
Copies points from existing list using the same dwell times, but different output settings.
Cop-
ies the contents of the dwell entries in the list from the start point to the end point and adds them to the
end of the list.
The setting value for each copied point is defined by the value in the array. This process
is repeated until either a) an invalid programmed current or voltage is found, b) the all entries in the
array have been copied or c) the list is full.
This command must be preceded by LIST:CURR or LIST:VOLT command and the starting and end
point values must be valid, otherwise a -221 “Settings conflict” error results. The entries on the dwell
list must match the values in the current or voltage list, otherwise a -226 “Not Same Length” error
results. (See Figures B-8 and B-9.)
Summary of Contents for BOP-ME 1KW
