KEB COMBIVERT F4-C, Applications Manual

Page: 272 / 283

ANTRIEBSTECHNIK
13 1 5
KEB COMBIVERT F4-C
Name: Basis
25.03.98
13
Annex Search and Find
Section Page Date
© KEB Antriebstechnik, 1997
All Rights reserved
Chapter
Input
characteristics amplifier 6.2.6
coded set selection 6.8.6
signals 6.2.4, 6.3.3
status 6.3.8
Installation and connection 7.1.3
InterBus
Loop 11.1.9
Loop-Operator 11.1.9
Operator 11.1.3
Interface
Operator 11.1.3, 11.1.4
type 6.10.3
Introduction 1.1.7
Inverter Address 11.2.3
Inverting
inputs 6.3.5
outputs 6.3.13
conditions 6.3.12
IR compensation 6.11.6
K
Keep on running 6.7.3
L
LA-/LD-Stop 4.3.11, 6.3.11, 6.7.3
LA-Stop 13.1.11
LAS 6.3.11
LE-parameter 6.3.11
LE.35 6.9.17
LE.41 6.1.14, 6.9.18
LE.44...46 6.9.18
LE.46 6.9.17
LE.47 6.9.17
LED 4.4.3
LON-Bus 11.1.3
Operator 11.1.3
M
Maximum
constant current
4.3.3, 4.3.7, 6.7.5
frequency 4.3.3, 4.3.6
mode 6.5.3
ramp current 4.3.3, 4.3.7
Minimum
frequency 4.3.3, 4.3.6, 6.4.9
MK/MN 6.6.3
Mode of rotation setting 6.4.7
Modulation 6.5.5
Motor
data 6.6.3
potentiometer
function 6.4.5, 6.9.13, 6.9.14
target 6.9.15
presetting 6.6.3
protection electronic 6.7.9
protective relay 6.3.11
rating plate 6.6.3
stator resistance 6.6.4
Multifunction Input 6.2.4
N
Network 11.1.3
components 11.1.3
Noise Filter 6.2.4
NPN 3.1.7
O
Offset X 6.2.6
Offset Y 6.2.6
OH 4.3.11
oP-parameter 5.1.3
oP. 0 6.4.6, 6.4.8, 6.9.15
oP. 0... 7 6.4.5
oP. 3 6.4.6
oP. 4... 9 6.4.9
oP.10 6.4.12, 6.4.16
oP.11...14 6.4.13
oP.15...18 6.4.14
oP.22 6.4.11
oP.25 6.4.11
oP.26...29 6.9.14
oP.28 6.9.15
oP.31 6.9.15, 6.11.11
oP.32 6.11.11
Optical fibre
BUS 11.1.5
interface description 11.1.6
operator description 11.1.6
Option 6.2.3
Optional analog input 6.2.4
Out1 6.3.10
Out2 3.1.6, 6.3.10
Out3 6.3.10
Output
characteristics amplifier 6.2.9
condition 6.3.10
interconnection 6.3.12
signals 6.2.8, 6.3.10
terminal status 6.3.13
Over
-heating warning 6.3.10
-load warning 4.3.11, 6.3.10
-modulation 6.5.5
-temperature warning 4.3.11
P
P-component 6.9.9
Parameter 4.1.3, 5.1.3
designation 4.1.3
groups 4.1.3, 5.1.3
missing 3.1.4
non-programmable 4.1.5, 6.8.3
set 4.1.3, 6.8.3
copying 6.8.3
lock 6.8.6
ON/OFF delay 6.8.7
sets
locking 6.8.6
value 4.1.3
Password 4.2.4
input 4.3.3, 4.3.4
levels 4.2.3
structure 4.2.3
Peak load 4.3.3, 4.3.5
Percent
actual value 11.2.7
reference value 11.2.7
setpoint value 11.2.6
PI
controller 6.4.5, 6.11.3
frequency limit 6.11.11
reset conditions 6.11.3
PLS 6.3.11
Pn-parameter 5.1.3
Pn. 0... 2 6.7.8
Pn. 3 6.3.11, 6.7.9
Pn. 4... 6 6.7.3
Pn. 6 6.1.6
Pn. 7 6.7.8
Pn. 8 6.9.3
Pn. 9 6.9.3
Pn.11 6.9.3
Pn.12 6.7.5
Pn.13 6.1.6
Pn.14 6.7.5
Pn.15 6.7.9
Pn.16 6.1.5, 6.7.10
Pn.17 6.9.7, 6.9.10
Pn.18 6.9.7