Kärcher B 90 R Series, Operating Instructions Manual

Page: 17 / 244

English
17
setting to 0% and set the cleaning program
with water at the programme selection
switch.
Note
The appliance is equipped with a fresh wa-
ter level display. If the fresh water tank is
empty, then the function of adding deter-
gent gets deactivated. The cleaning head
continues to work without the addition of
any liquid.
Figure 7, see cover page
1 Driving
Driving to the Place of Use.
2 Scrubbing suction
Wet clean the floor and vacuum up dirt
water.
3 Wet scrubbing
Wet clean the floor and allow the deter-
gent to react.
4 Vacuuming
Suck in the dirt fleet.
5 Polishing
Polishing the floor without the applica-
tion of liquid.
6 Scrub the floor without applying water
(vacuum polishing)
Polish the floor without applying any flu-
id and suck in the polishing dust.
Note
Depending on the programme, the vacuum
bar and the cleaning head must be lowered
using the respective controls in order to ex-
ecute the selected programme.
Use the Info button to select the menu items
and do the settings.
– Turning the button to the right/left scrolls
through the menus forward/ backward.
– The selected setting gets accepted by
pressing the button.
You can make the settings for the different
cleaning programs in the operator menu.
Different parameters can be set based on
the cleaning program. The settings are
done using the Info button.
Î Release emergency-stop button by
turning.
Î Sit on the seat and set main switch to
"1".
The display shows the battery charging
status and the fresh water level.
Î Select cleaning program.
Î Call the operator menu by turning the
info button.
Î Select the desired parameter by turning
the Info button.
Î Press Info button - the set value blinks.
Î Reset the parameter by turning the info
button.
Î Accept modified setting by pressing the
Info button or wait till the set value is ac-
cepted automatically.
Note
If the selected parameter does not change
within 10 seconds, then the display goes
back to displaying the battery charging sta-
tus and the fresh water level.
The same cleaning parameter can have in-
dividual settings for each cleaning program.
All settings are saved even in the powerless
state of the machine.
Î Turn the info button until "Information-
menu" is displayed.
Î Retrieve the info menu by pressing the
info button.
The following information can be displayed
by turning the info button:
Î Set the water quantity at the regulation
knob according to the dirt level and the
type of flooring.
Î Press down the rear surface of the ped-
al to raise/lower the cleaning head, re-
lease and let the pedal move upwards.
The brush drive will start as soon as the
cleaning head is lowered.
Î Press down the front surface of the ped-
al to raise/lower the cleaning head and
lock it.
Î Pull the lever up to raise/lower the vac-
uum bar, press toward the outside and
lower.
The suction process will start as soon
as the level is moved down.
Î Pull the lever to raise and lower the vac-
uum bar up and lock.
To improve the vacuuming result on tiled
floors the vacuum bar can be turned to an
oblique position of up to 5°.
Figure 8, see cover page
Î Release the wing nuts.
Î Turn the vacuum bar.
Î Tighten the wing nuts.
If the vacuum result is unsatisfactory the in-
clination of the straight vacuum bar can be
modified.
Figure 8, see cover page
Î Release the wing nuts.
Î Tilt the vacuum bar.
Î Tighten the wing nuts.
Figure 10, see cover page
Î Unlock the lever for the brush contact
pressure to the left and relock to the
right.
– Level down: Reduce contact pressure.
– Level up: Increase contact pressure.
Î Adjust the wiper flaps by turning the ad-
justment wheel so that they touch the
floor.
Î
Turn the adjustment wheel an additional
turn toward the bottom.
Note
Overflow dirt water tank. If the dirt water
tank is full, the suction turbine switches off
and the indicator lamp "dirt water tank full"
begins to blink. All cleaning programs with
suction are blocked for one minute. Empty
the dirt water reservoir.
Cleaning Programs
Info button (only Adv. model)
Settings (only Adv. model)
Operator menu
Adjustable parameters
Adjustable pa-
rameters min:ste
p:max Remark
Cleanspeed (max.
cleaning speed) 1:1:6 1=1km/h,
6=6km/h
FACT (brush
speed) – Power
Whisper
Fine
Vacuum (suction
performance) – Low
High
Only with Dose model
Chemical/Agent
(detergent meter-
ing) 0,5%:0,
5%:3% –
Info menu
Display Significance
Ophrs xx Operating hour
counter
When the counter
is running, "+" will
be displayed
Water E-----F Water level in fresh
water tank
"C" blinks while the
metering pump is
operating (only
Dose model)
Speed: xkm/h Current speed
Alfred/Kärcher Manufacturer
B90R Dxx Appliance descrip-
tion
Prog.Vers. x.x Softwareversion
Exit Inform.menu Exit the info menu
by pressing the
info button.
Setting the water quantity
Raise/lower the cleaning head
Lower
Raise
Raise/lower the vacuum bar
Lower
Raise
Setting the Vacuum Bar
Oblique position
Inclination
Adjust brush contact pressure (only
with the Adv model)
Adjust wiper flaps (only with the
Adv model)
Emptying the Dirt Water Reservoir