JUKI APW-896N/IP-420 Instruction Manual Download Page 4

Page: 4 / 142

iii

VII. MAINTENANCE ...........................................................................................................99

1. INSPECTION ...................................................................................................................................... 99

(1) Maintenance and inspection of the pneumatic device

.................................................................... 99

(2) Maintenance and inspection related to the sewing machine .......................................................... 99

(3) With regard to the waste oil of the hook oil

...................................................................................

100

(4) With regard to the cleaning of the hook shaft base

.......................................................................

100

2. MARKING LIGHT.............................................................................................................................. 101

(1) Fixed marking (standard) ..............................................................................................................

101

(2) Movable marking (optional)...........................................................................................................

101

(3) Adjusting the marking light irradiation position

..............................................................................

102

(1) Replacing procedure between double-welt and single-welt

..........................................................

109

(2) Fine adjustment of the position of garment body clamp

...............................................................

109

(3) Replacing the binder ......................................................................................................................

110

8. ADJUSTING THE CORNER KNIFE ..................................................................................................111

(1) Corner knife unit

.............................................................................................................................111

(2) Adjusting the corner knife

...............................................................................................................112

(3) Corner knife adjustment function screen

.......................................................................................113

(4) Corner knife actuating position setting procedure

..........................................................................115

(5) Feature of the corner knife actuating position setting

....................................................................116

(6) Deflection amount setting

..............................................................................................................118

9. CENTER KNIFE ................................................................................................................................ 119

(1) Center knife actuating position setting procedure

..........................................................................119

(2) Feature of the center knife actuating position setting

...................................................................

120

10. ADJUSTING THE POSITION OF THE SENSOR FOR DETECTING FLAPS ................................................... 122
11. CAUSES AND CORRECTIVE MEASURES AGAINST TROUBLES WITH THE BOBBIN THREAD REMAINING

AMOUNT DETECTING DEVICE ........................................................................................................................... 123

12. HOW TO ADJUST THE FOOT PEDAL ............................................................................................ 124
13. ERROR CODE LIST ......................................................................................................................... 126
14. INPUT NUMBER TABLE .................................................................................................................. 138

Summary of Contents for APW-896N/IP-420















































































































































Search results

Summary of Contents for APW-896N/IP-420

Reviews:

JUKI APW-896N/IP-420, Instruction Manual, Page: 4 / 142

Search results

Summary of Contents for APW-896N/IP-420

Reviews: