JUKI APW-896N/IP-420 Instruction Manual Download Page 56

Page: 56 / 142

− 52 −

(2) Sewing data list

①

Items that are displayed in the data input screen

※

. . . Item that is not displayed due to other setting state

No.

Item

Setting range

Edit unit

Initial value

Motion mode change-over

With/without of motion of sewing machine motor, center knife and corner
knife is selected.

- - -

Cloth feed mode

Cloth feed, sewing

machine thread trimming

and center knife mode

Cloth feed, sewing ma-

chine thread trimming

Cloth feed, sewing machine

thread trimming, center

knife and corner knife mode

Sewing mode change-over

Sewing mode is selected.

* In case of alternate sewing, flap priority sewing is set with

- - -

L size sewing

Left flap sewing

Right flap sewing

Flap priority sewing

L size setting

In case of L size sewing, the sewing length is set.
* It is possible to set only when setting L size sewing

18.0 to

220.0

0.1mm

150.0mm

※

Marking light irradiation position change-over

Sewing start irradiation/sewing end irradiation/center irradiation is selected.

- - -

Sewing start irradiation

Sewing end irradiation

Center irradiation

Flap concealed stitching data (Left sewing start)

Position of sewing start of left-hand flap is adjusted.
* It is possible to set only when

is set to flap sewing.

–9.9 to 9.9

0.1mm

0.0mm

※

Flap concealed stitching data (Left sewing end)

Position of sewing end of left-hand flap is adjusted.
* It is possible to set only when

is set to flap sewing.

–9.9 to 9.9

0.1mm

0.0mm

※

Flap concealed stitching data (Right sewing start)

Position of sewing start of right-hand flap is adjusted.
* It is possible to set only when

is set to flap sewing.

–9.9 to 9.9

0.1mm

0.0mm

※

Summary of Contents for APW-896N/IP-420















































































































































Search results

Summary of Contents for APW-896N/IP-420

Reviews:

JUKI APW-896N/IP-420, Instruction Manual, Page: 56 / 142

Search results

Summary of Contents for APW-896N/IP-420

Reviews: