JUKI APW-896N/IP-420 Instruction Manual Download Page 24

Page: 24 / 142

− 20 −

❷

❶

6. HOW TO ADJUST THE THREAD TENSION

Bobbin

Bobbin case

Bobbin thread

tension adjustment

screw

②

Adjusting needle thread tension

First, adjust the right- and left-hands bobbin

thread tension.

Then in accordance with the bobbin thread

tension obtained, adjust the right- and left-hand
sides needle threads tension appropriately by
turning thread tension adjustments nuts

❶

and

❷

respectively. Turning the nuts clockwise will

increase the thread tension or turning them
counterclockwise to decrease it.

①

Adjusting bobbin thread tension

Turn bobbin thread tension adjustment screw

clockwise to increase the bobbin thread tension
or turn the screw counterclockwise to decrease it.

As shown in the left-hand figure, standard
bobbin thread tension is 0.25 to 0.35N when

measuring with the tension gauge.

Summary of Contents for APW-896N/IP-420















































































































































Search results

Summary of Contents for APW-896N/IP-420

Reviews:

JUKI APW-896N/IP-420, Instruction Manual, Page: 24 / 142

Search results

Summary of Contents for APW-896N/IP-420

Reviews: