JUKI APW-896N/IP-420 Instruction Manual Download Page 80

Page: 80 / 142

− 76 −

(1) Changing procedure of the device setting

11. CHANGING THE DEVICE SETTING

①

Displaying the 2nd screen of the operation-mode changeover

screen.

When you keep operation-mode changeover key

held

pressed for six seconds, right-scroll button

is displayed

on the screen.

When you press this button, the 2nd screen (screen A) of the op-
eration-mode changeover screen is displayed.

②

Displaying the device setting list screen

Device setting button

is displayed on the screen.

When you press this button, the device setting list screen is dis-
played.

③

Selecting the device setting you want to change

Select the data item button

you want to change.

Second screen of the

mode changeover screen

(Screen A)

Device setting list screen

(Screen B)

Summary of Contents for APW-896N/IP-420















































































































































Search results

Summary of Contents for APW-896N/IP-420

Reviews:

JUKI APW-896N/IP-420, Instruction Manual, Page: 80 / 142

Search results

Summary of Contents for APW-896N/IP-420

Reviews: