manualshive.com logo in svg

JUKI APW-896N/IP-420, Instruction Manual, Page: 100 / 142

Share
Download
JUKI APW-896N/IP-420 Instruction Manual Download Page 100

− 96 −

(5) Take-in of plural data together

①

  Display the writing file selection screen

 

Press PLURAL SELECTION button 

 

A

 and the data No. 

plural selection screen is displayed.

No.99 and after of the media cannot perform the plural selection.

②

  Perform the selection of data No.

 

List of the file No. of the existing data is displayed. Press FILE No. 

buttons 

B

 you desire to write. It is possible to reverse the selec-

tion state of the button with REVERSE button 

 

C

.

③

  Determine the data No.

 

When ENTER button 

 

D

 is pressed, the data No. plural se

-

lection screen is closed and the selection of data ends.

④

  Start the communication

 

Press COMMUNICATION START button 

 

E

 and the data 

communication starts.

It is possible for the sewing data to select plural data to be written and write all together. Pattern No. of writ-
ing destination is the same No. of the selected data No.

A

C

D

E

B

Summary of Contents for APW-896N/IP-420















































































































































Reviews:

No comments