manualshive.com logo in svg

JUKI APW-896N/IP-420, Instruction Manual, Page: 28 / 142

Share
Download
JUKI APW-896N/IP-420 Instruction Manual Download Page 28

− 24 −

①

   Precautions to be taken when handling USB devices

  •   Do not leave the USB device or USB cable connected to the USB port while the sewing machine is in 

operation. The machine vibration can damage the port section resulting in loss of data stored on the 
USB device or breakage of the USB device or sewing machine.

  •    Do not insert/remove a USB device during reading/writing a program or sewing data.
 

It may cause data breakage or malfunction.

  •   When the storage space of a USB device is partitioned, only one partition is accessible.
  •   Some type of the USB device may not be properly recognized by this sewing machine.
  •  JUKI does not compensate for loss of data stored on the USB device caused by using it with this sewing 

machine. 

  •   When the panel displays the communication screen or pattern data list, the USB drive is not recognized 

even if you insert a medium into the slot.

  •    For USB devices and media such as CF

(TM)

 cards, only one device/medium should be basically con-

nected/inserted to/into the sewing machine. When two or more devices/media are connected/inserted, 
the machine will only recognize one of them. Refer to the USB specifications.

  •  Insert the USB connector into the USB terminal on the IP panel until it will go no further.

  

•  Do not turn the power OFF while the data on the USB flash drive is being accessed.

②

   USB specifications

•   Conform to USB 1.1 standard
•   Applicable devices *

1 �����

Storage devices such as USB memory, USB hub, FDD and card reader

•   Not-applicable devices

 ����

CD drive, DVD drive, MO drive, tape drive, etc.

•   Format supported  �������

FD (floppy disk) FAT 12

 

Others (USB memory, etc.), FAT 12, FAT 16, FAT 32

•   Applicable medium size

 ���

FD (floppy disk) 1.44MB, 720kB

 

Others (USB memory, etc.), 4.1MB ~ (2TB) 

•   Recognition of drives 

 �����

For external devices such as a USB device, the device which is recog-
nized first is accessed. However, when a medium is connected to the built-
in media slot, the access to that medium will be given the highest priority. 
(Example : If a medium is inserted into the media slot even when the USB 
memory has already been connected to the USB port, the medium will be 

accessed.)

•   Restriction on connection ��

Max. 10 devices (When the number of storage devices connected to the 

sewing machine has exceeded the maximum number, the 11th storage de

-

vice and beyond will not be recognized unless they are once disconnected 
and re-connected. )

•   Consumption current  �����

The rated consumption current of the applicable USB devices is 500 mA at 

the maximum.

  *

1 

: JUKI does not guarantee operation of all applicable devices. Some device may not operate due to a 

compatibility problem.

Summary of Contents for APW-896N/IP-420















































































































































Reviews:

No comments