manualshive.com logo in svg

JUKI APW-896N/IP-420, Instruction Manual, Page: 138 / 142

Share
Download
JUKI APW-896N/IP-420 Instruction Manual Download Page 138

− 134 −

Error code

Description of error

How to recover

E486

Flap sewing data cannot be sewn.

Possible to re-
start after reset.

E487

Both long presser and endless zipper are simultaneously 

selected.

Possible to re-
start after reset.

E488

- - - 

The gauge size exceeds the input range.

Possible to re-
start after reset.

E489

Combination data other than right/left flap sewing is set at 
the time of flap priority setting of alternate sewing mode.

Possible to re-
start after reset.

E490

It is not possible to feed up to corner knife position.

When flap is put on this side in case of the long type

Possible to re-
start after reset.

E491

Corner knife length is too short.

When knife cannot be entered since the interval of corner knife is 

short.

Possible to re-
start after reset.

E492

L size length is too short.

When sewing cannot be performed since the inputted L size 

length is too short

Possible to re-
start after reset.

E493

L size length is too long.

When sewing cannot be performed since the inputted L size 

length is too long.

Possible to re-
start after reset.

E494

Center knife length error

When center knife length is smaller than knife size of 6.7 mm

Possible to re-
start after reset.

E495

Length at sewing start/sewing end over

When sewing length is shorter than the total of length of each 

condensation (back tack) at sewing start and sewing end

Possible to re-
start after reset.

Summary of Contents for APW-896N/IP-420















































































































































Reviews:

No comments