JUKI APW-896N/IP-420 Instruction Manual Download Page 78

Page: 78 / 142

− 74 −

10. PERFORMING OPTIONAL SETTING

(1) Changing procedure of the optional setting

Optional setting list

screen (Screen B)

①

Displaying the 2nd screen of the operation-mode changeover

screen.

When you keep operation-mode changeover key

held

pressed for six seconds, right-scroll button

is displayed

on the screen.

When you press this button, the 2nd screen (screen A) of the op-
eration-mode changeover screen is displayed.

②

Displaying the option setting list screen

Option setting button

is displayed on the screen.

When you press this button, option setting list screen (screen B)
is displayed.

③

Selecting the option setting you want to change

Press up/down scroll buttons

to select the data item

button

you want to change.

Second screen of the

mode changeover screen

(Screen A)

Summary of Contents for APW-896N/IP-420















































































































































Search results

Summary of Contents for APW-896N/IP-420

Reviews:

JUKI APW-896N/IP-420, Instruction Manual, Page: 78 / 142

Search results

Summary of Contents for APW-896N/IP-420

Reviews: