manualshive.com logo in svg

JUKI APW-896N/IP-420, Instruction Manual, Page: 66 / 142

Share
Download
JUKI APW-896N/IP-420 Instruction Manual Download Page 66

− 62 −

No.

Item

Setting range

/

Edit unit

Initial value

Jump feed speed up to the position of sewing start

Jump feed speed up to the position of sewing start is set.

3 to 10

/

1

5

Jump feed speed up to the position of corner knife

Jump feed speed up to the position of corner knife is set.

3 to 10

/

1

5

Dart stretcher device stop/motion change-over

Stop/motion of dart stretcher device is selected.
* It is possible to set only when 

 dart stretcher option is used.

- - -

※

Stop

Motion

Automatic interlining supplying device stop/motion change-over

Stop/motion of automatic interlining supplying device is selected.
* It is possible to set only when 

 automatic interlining supplying 

option is used.

* Regarding the interlining supplying, when the pattern is not used, be 

careful not to make the interlining come out from the top surface of the 
table. When using next, press once the feeding button on the panel and 
perform the feeding motion to cut.

- - -

※

Stop

Motion

Flap length

Length of flap is set.
It is possible to set only when 

 automatic interlining supplying de-

vice is selected to motion and 

 sewing mode changeover is select

-

ed to flap sewing.

*  This setting is set to determine the interlining feeding length of automatic 

interlining supplying device. Sewing length is determined by the detection 
of flap sensor.

37.0 to 

220.0

/

0.1mm

150.0mm

※

Sewing speed under the high-speed mode

Number of revolutions at lockstitch section is set.
* It is possible to set only when 

 sewing speed setting selection is 

set to pattern data selection.

1000 to 

3000

/

100sti/min

2500sti/min

※

Sewing speed under the low-speed mode

Number of revolutions at condensation and back tack sewing sections is set.
* It is limited by 

 sewing speed under the high-speed mode.

* It is possible to set only when 

 sewing speed setting selection is 

set to the selection of pattern data.

* In case of back tack sewing, the upper limit of number of revolutions of 

the actual low speed is limited to 1,500 sti/min.

1000 to 

2500

/

100sti/min

1500sti/min

※

※

. . . Item that is not displayed due to other setting state

Summary of Contents for APW-896N/IP-420















































































































































Reviews:

No comments