manualshive.com logo in svg

JUKI APW-896N/IP-420, Instruction Manual, Page: 18 / 142

Share
Download
JUKI APW-896N/IP-420 Instruction Manual Download Page 18

− 14 −

V. PREPARATION OF THE SEWING MACHINE

1. HOW TO OPERATE THE SEWING MACHINE HEAD

(1) How to attach the needles

Needles used are DP X 17 #14 to #18 (standard 
#16). Use the specified needle.
Insert left- and right-hand sides needles as far as 
they will go pointing their long grooves 

❶

 at each 

other and tighten needle clamp screws 

❷

.

•  Use the left hand twist thread for the needle 

thread.

•  Either twist thread will do for the bobbin thread.

(2) Thread used

Right hand twist thread

Left hand twist thread

Use a new thread which is uniformly 

twisted.

CAUTION 

: 

•  Turn OFF the power before starting the work so as to prevents accidents caused by abrupt start of 

the sewing machine.

•  When replacing the needle, be careful not to allow your fingers to touch the blade section of the 

center knife.

❷

❷

❶

Summary of Contents for APW-896N/IP-420















































































































































Reviews:

No comments