JUKI APW-896N/IP-420 Instruction Manual Download Page 126

Page: 126 / 142

− 122 −

10. ADJUSTING THE POSITION OF THE SENSOR FOR DETECTING FLAPS

①

Adjust the positions of both right and left sen-

sors for detecting flaps to outside of 4.5 to 5 mm
from the needle entry and the sewing direction
(longitudinal direction) of both right and left sen-
sors to the position of 37 mm from the needle
entry on the operator side.

Adjust the position of sensor for detecting flap
angle to 0.5mm on the needle center side from
the center of the reflecting tape on the flap base

and the sewing direction (longitudinal direction)

to the position of 37 mm on the operator side.

④

Adjust the lateral direction of sensor for detect-

ing right flap

❹

by loosening setscrews

❺

and

moving the sensor in the lateral direction.

⑤

Adjust the sewing direction of sensor for de-

tecting right flap

❹

by loosening screws

❻

and

moving the sensor in the longitudinal direction.

After the adjustment, be sure to perform

trial sewing and adjust the flap sewing

position with the panel.

②

Adjust the lateral direction of sensor for de-

tecting left flap and flap angle detection sensor

❶

by loosening setscrews

❷

and moving the

sensors together with sheet metal in the lateral
direction.

③

Adjust the sewing direction of sensor for de-

tecting left flap and flap angle detection sensor

❶

by loosening setscrews

❸

and moving the

sensors in the longitudinal direction.

Right flap

sensor light

Left flap sensor light

Needle entry

Angle detection sensor light

5mm

37mm

It is not necessary to loosen setscrews

❼

when adjusting the position of sen

sors.

❶

❼

❸

❻

❺

❹

❷

❼

Summary of Contents for APW-896N/IP-420















































































































































Search results

Summary of Contents for APW-896N/IP-420

Reviews:

JUKI APW-896N/IP-420, Instruction Manual, Page: 126 / 142

Search results

Summary of Contents for APW-896N/IP-420

Reviews: