Alarm system JA-60 "COMFORT"
- 20 -
MDY51319
Note: enter a pause (F0) after the last digit of a number which is calling a mobile phone. This way the number will be
called only once and the dialer will not check the line signals (some mobile phone systems do not generate standard
telephone line signals).
When activated, the dialer will
disengage all other devices hooked up to the phone line (telephone, fax..). It will then,
one by one, call and play the user recorded message, for all programmed numbers. If the dialer makes a successful
connection to a programmed number, it will not call that number again. If the number is busy, the dialer will make 3 more
attempts to call it.
Empty tel. number memories are skipped. If all memories are empty, the dialer is completely disabled.
To delete a telephone number
enter:
7 F0 Fy
where
y
is a memory number from 1 to 4
entering
7 F0 F0
will erase all tel. numbers, including the Pager number
Store number to call Pager
(to memory number 5) entering:
7 xx..x F9 zzz....zz F5
where
xx...x
= provider prefix
F9
= separator
(it will wait for a provider’s signal and will switch to DTMF if not used)
zzz...zz
= pager number and numeric message and other specific codes (language selec-
tors, end of message etc.) if requested by the Paging provider
F5
= to store the number to memory no. 5
As a maximum 32 digits can be stored to memory # 5. Special characters can be entered with the following Fx codes:
pause
F0
∗
F7
#
F8
Example: enter 7 0611 F9 1 1234 555 F80 F5 if the provider prefix is 0611, the Pager number 1234 and the message
555. Number 1 after F9 is a language selector, code F80 represents
#0
= end of message.
Note: some Paging providers also offer an option to send the message as an SMS to the GSM network. Consult your
Paging provider for details if you have trouble sending a message to the Pager.
To delete the Pager number
enter:
7 F0 F5
If the memory number 5 is empty, no message will be sent to a Pager.
Factory default setting: all memories from 1 to 5 are empty.
9.2. Voice message recording
sequence: 8 0
Press shortly key
8
then press key
0
and hold it pressed while talking into the control panel’s front grid (max. 20 sec-
onds). After releasing the 0 key, the message will play back. The message is stored in non-volatile memory and can be
changed when ever you want to by repeating the above steps. Make the message clear and brief. The dialer repeats the
message to each called number for 40 seconds.
It is possible to
split the voice message into two different messages
(10 seconds each). Depending on the setting in
section 9.5., a particular message will be sent under different situations.
If you want
to record two messages
: press shortly key
8
and then press key
1
and hold it pressed while recording the
first message. To record the second message press shortly key
8
then press key
2
and hold it pressed while talking into
the control panel’s front grid.
9.3. Telephone dialer testing
sequence: 8 9
Enter
89
and the dialer will call the programmed numbers once. You will hear the telephone line signals from the built in
speaker during the test (if the dialer is triggered by an alarm in normal operation, it will call silently). Testing can be termi-
nated with the
N
key.
If two different voice messages were recorded, then use sequence 88 to test the sending of the first message and 89 to
test the sending of the second message.
Summary of Contents for JA-60 "Comfort"
Page 1: ...JA 60 COMFORT Alarm system Installation manual...
Page 2: ......
