background image

13. Monitoring station reporting codes table 

  

A two digit reporting code 

rc 

(00 to FFh) can be set for every event. If 00 is programmed as a report code, that event will 

not be reported.  
 The major events group is marked with 

Rc. 

When formats 3/1 or 4/1/1 are used, only these major events are reported to 

the Monitoring Station. This makes it necessary to only program the

 R 

digits. The second digit does not count. 

For Contact ID protocol, program code 11 for major events (

Rc

) which you want to report and the system will generate all 

details regarding the event automatically.  

 

Alarm system JA-60 “COMFORT” 

- 26 - 

MDY51319

 

N. Event 

Code 

001 Arming with remote control N.1 

Rc 

002 Arming with remote control N.2 

rc 

003 Arming with remote control N.3 

rc 

004 Arming with remote control N.4 

rc 

005 Arming with remote control N.5 

rc 

006 Arming with remote control N.6 

rc 

007 Arming with remote control N.7 

rc 

008 Arming with remote control N.8 

rc 

009 Arming with master code 

rc 

010 Arming with user code N.1 

rc 

011 Arming with user code N.2 

rc 

012 Arming with user code N.3 

rc 

013 Arming with user code N.4 

rc 

014 Arming with user code N.5 

rc 

015 Arming with user code N.6 

rc 

016 Arming with user code N.7 

rc 

017 Arming with user code N.8 

rc 

018 Arming with user code N.9 

rc 

019 Arming with user code N.10 

rc 

020 Arming with user code N.11 

rc 

021 Arming with user code N.12 

rc 

022 Arming with user code N.13 

rc 

023 Arming with user code N.14 

rc 

024 Partial arming 

Rc 

025 Quick arming without code 

Rc 

026 Disarming with remote control N.1 

Rc 

027 Disarming with remote control N.2 

rc 

028 Disarming with remote control N.3 

rc 

029 Disarming with remote control N.4 

rc 

030 Disarming with remote control N.5 

rc 

031 Disarming with remote control N.6 

rc 

032 Disarming with remote control N.7 

rc 

033 Disarming with remote control N.8 

rc 

034 Disarming with master code 

rc 

035 Disarming with user code N.1 

rc 

036 Disarming with user code N.2 

rc 

037 Disarming with user code N.3 

rc 

038 Disarming with user code N.4 

rc 

039 Disarming with user code N.5 

rc 

040 Disarming with user code N.6 

rc 

041 Disarming with user code N.7 

rc 

042 Disarming with user code N.8 

rc 

043 Disarming with user code N.9 

rc 

044 Disarming with user code N.10 

rc 

045 Disarming with user code N.11 

rc 

046 Disarming with user code N.12 

rc 

047 Disarming with user code N.13 

rc 

048 Disarming with user code N.14 

rc 

049 Entering of the programming mode 

Rc 

050 Exiting the programming mode 

Rc 

051 Communicator Reset 

Rc 

052 Initial AC powering 

Rc 

053 Alarm after initial AC powering 

Rc 

054 General battery trouble 

Rc 

055 General battery trouble end 

Rc 

056 Control panel battery trouble 

Rc 

057 Control panel battery trouble end 

Rc 

058 Zone alarm 1

 

Rc 

059 Zone alarm 2

 

rc 

060 Zone alarm 3

 

rc 

061 Zone alarm 4

 

rc 

062 Zone alarm 5

 

rc 

063 Zone alarm 6

 

rc 

064 Zone alarm 7

 

rc 

065 Zone alarm 8

 

rc 

066 Zone alarm 9

 

rc 

067 Zone alarm 10

 

rc 

068 Zone alarm 11

 

rc 

069 Zone alarm 12

 

rc 

070 Zone alarm 13

 

rc 

071 Zone alarm 14

 

rc 

072 Zone alarm 15

 

rc 

073 Zone alarm 16

 

rc 

074 Wrong access code alarm 

Rc 

075 Zone tamper 1

 

Rc 

076 Zone tamper 2

 

rc 

077 Zone tamper 3

 

rc 

078 Zone tamper 4

 

rc 

079 Zone tamper 5

 

rc 

080 Zone tamper 6

 

rc 

081 Zone tamper 7

 

rc 

082 Zone tamper 8

 

rc 

083 Zone tamper 9

 

rc 

084 Zone tamper 10

 

rc 

085 Zone tamper 11

 

rc 

086 Zone tamper 12

 

rc 

087 Zone tamper 13

 

rc 

088 Zone tamper 14

 

rc 

089 Zone tamper 15

 

rc 

090 Zone tamper 16

 

rc 

091 Keypad tamper 

rc 

092 Control panel tamper 

rc 

093 Siren tamper 

rc 

094 Zone fault 1

 

Rc 

095 Zone fault 2

 

rc 

096 Zone fault 3

 

rc 

097 Zone fault 4

 

rc 

098 Zone fault 5

 

rc 

099 Zone fault 6

 

rc 

100 Zone fault 7

 

rc 

101 Zone fault 8

 

rc 

102 Zone fault 9

 

rc 

103 Zone fault 10

 

rc 

104 Zone fault 11

 

rc 

105 Zone fault 12

 

rc 

106 Zone fault 13

 

rc 

107 Zone fault 14

 

rc 

108 Zone fault 15

 

rc 

109 Zone fault 16

 

rc 

110 Keypad fault 

rc 

111 Control panel fault 

rc 

112 Siren fault 

rc 

113 Zone alarm end 1 

Rc 

114 Zone alarm end 2

 

rc 

115 Zone alarm end 3

 

rc 

116 Zone alarm end 4

 

rc 

117 Zone alarm end 5

 

rc 

118 Zone alarm end 6

 

rc 

119 Zone alarm end 7

 

rc 

120 Zone alarm end 8

 

rc 

121 Zone alarm end 9

 

rc 

122 Zone alarm end 10

 

rc 

123 Zone alarm end 11

 

rc 

124 Zone alarm end 12

 

rc 

125 Zone alarm end 13

 

rc 

126 Zone alarm end 14

 

rc 

127 Zone alarm end 15

 

rc 

128 Zone alarm end 16

 

rc 

129 Zone tamper end 1 

Rc 

130 Zone tamper end 2

 

rc 

131 Zone tamper end 3

 

rc 

132 Zone tamper end 4

 

rc 

133 Zone tamper end 5

 

rc 

134 Zone tamper end 6

 

rc 

135 Zone tamper end 7

 

rc 

136 Zone tamper end 8

 

rc 

137 Zone tamper end 9

 

rc 

138 Zone tamper end 10

 

rc 

139 Zone tamper end 11

 

rc 

140 Zone tamper end 12

 

rc 

141 Zone tamper end 13

 

rc 

142 Zone tamper end 14

 

rc 

143 Zone tamper end 15

 

rc 

144 Zone tamper end 16

 

rc 

145 Keypad tamper end 

rc 

146 Control panel tamper end 

rc 

147 Siren tamper end 

rc 

148 Zone fault end 1 

Rc 

149 Zone fault end 2

 

rc 

150 Zone fault end 3

 

rc 

151 Zone fault end 4

 

rc 

152 Zone fault end 5

 

rc 

153 Zone fault end 6

 

rc 

154 Zone fault end 7

 

rc 

155 Zone fault end 8

 

rc 

156 Zone fault end 9

 

rc 

157 Zone fault end 10

 

rc 

158 Zone fault end 11

 

rc 

159 Zone fault end 12

 

rc 

160 Zone fault end 13

 

rc 

161 Zone fault end 14

 

rc 

162 Zone fault end 15

 

rc 

163 Zone fault end 16

 

rc 

164 Keypad fault end 

rc 

165 Control panel fault end 

rc 

166 Siren fault end 

rc 

167 Telephone line trouble 

Rc 

168 Telephone line trouble end 

Rc 

169 Control panel failure 

Rc 

170 End of control panel failure 

Rc 

171 Periodic test (24 hr. from last com.) 

Rc 

172 AC failure (in 30 min. after failure) 

Rc 

173 AC failure end  

Rc 

174 RF jamming 

Rc 

175 Wrong code alarm end 

Rc 

176 RF jamming end 

Rc 

177 Panic alarm  from remote control N.1  Rc 

178 Panic alarm from remote control N.2

 

rc 

179 Panic alarm from remote control N.3

 

rc 

180 Panic alarm from remote control N.4

 

rc 

181 Panic alarm from remote control N.5

 

rc 

182 Panic alarm from remote control N.6

 

rc 

183 Panic alarm from remote control N.7

 

rc 

184 Panic alarm from remote control N.8

 

rc 

185 Master code panic alarm 

rc 

186 User code panic alarm 

rc 

187 Panic alarm  end from remote contr. 1 Rc 

188 Panic alarm end from remote control N.2 rc 
189 Panic alarm end from remote control N.3 rc 
190 Panic alarm end from remote control N.4 rc 
191 Panic alarm end from remote control N.5 rc 
192 Panic alarm end from remote control N.6 rc 
193 Panic alarm end from remote control N.7 rc 
194 Panic alarm end from remote control N.8 rc 
195 Master code panic alarm end 

rc 

196 User code panic alarm end 

rc 

197 Subsystem panic alarm 

Rc 

198 Subsystem panic alarm end 

Rc 

Summary of Contents for JA-60 "Comfort"



































Reviews: