jablotron JA-60 "Comfort", Installation Manual

Page: 24 / 34

12.2. Account code setting sequence: 02
This sequence is used for the alarm system identification by a Monitoring Station. The sequence structure is as follows:
02 x x x x
xxxx – account code ( x are numbers from 0 to 9 or hexadecimals).
When using only three-digit codes (formats 3/1 and 3/2) enter a zero in the first position. The communicator will then ig-
nore it (example - 0123)
Note: Changing of the account code erases the internal communicator’s memory of non reported events and sends a „Reset“ reporting
code (051) to the Monitoring Station.
Factory setting: 0000
12.3 Protocol and Format setting sequence: 03
This sequence is used to select the communication protocol and format. Its structure is as follows:
03 x y
x - protocol (0 – 9, see table bellow)
y - format (0 - 3 see table on right
)
Formats
y format reports structure
0 3/1 Major events only xxx R
1 3/2 All events xxx rc
2
4/1/1 Major events with autom.
source identification xxxx Rn
3 4/2 All events xxxx rc
xxxx = account number
R = major event code (first digit counts only)
rc = detailed event code (two digits)
n = source identification (generated automatically)
Surgard protocol has structure: xxxx E rc, where
E is a group identifier (generated automatically)
E Event Note
1 Fire
2 Panic
3 Alarm General
4 Arming
Incl. Partial
5 Disarming
6 Failure
Mains failure, RF jamming etc..
8 Report Enter/Exit service mode …
9 Restore End of alarm, panic …
A Test 24 hour test
Protocols
x Name
Hand-shake Data Kiss off Speed
format
0 Ademco Slow
(Si-
lent Knight)
1400Hz 1900Hz 1400Hz 10bps Next
table
1
Ademco Fast 1400Hz 1900Hz 1400Hz 14bps Next
table
2 Telemax
2100Hz 1650Hz 2100Hz 10bps Next
table
3 Franklin
2300Hz 1800Hz 2300Hz 20bps Next
table
4 Radionics 2300
2300Hz 1800Hz 2300Hz 40bps Next
table
5 Radionics 1400
1400Hz 1900Hz 1400Hz 40bps Next
table
6 DTMF 2300
2300Hz DTMF 2300Hz DTMF Next
table
7 Surgard* 2300Hz DTMF 2300Hz DTMF 4/3
8
Ademco express* Dual tone DTMF 1400Hz DTMF 4ID/2
9
Contact ID* Dual tone DTMF 1400Hz DTMF CID
*
fixed format , “y” is
arbitrary (0 is recommended)
Notes:
1/ Some Monitoring Station receivers do not support all formats.
2/ Logic of the format marking - 4/2 means, that an account code has
4 digits and an event report code has 2 digits.
Changing of a format erases the internal communicator’s memory of non reported events and sends a „Reset“ reporting code (051) to the
Monitoring Station.
Factory setting: 90 (Contac ID)
12.4. Re-dialing pause setting sequence: 04
If a dialer is triggered it attempts to make a connection (altering the main and the backup telephone number). If it is not
possible to make a connection after 8 attempts, a pause is inserted. After this pause the dialer dials again. If any event
triggers the communicator during the pause, the pause ends immediately. The pause length can be set in a following
way:
0 4 x
x – time multiplied by 10 minutes (from 1 to 9, example 3 = 30 minutes)
Factory setting: 1 = 10 min.
Alarm system JA-60 "COMFORT" - 24 - MDY51319