jablotron JA-60 "Comfort", Installation Manual

Page: 12 / 34

Alarm system JA-60 "COMFORT" - 12 - MDY51319
List of control panel programmable parameters
Function sequence options factory
d.
note
Enrolling of detectors and controllers
1
1 & 6 scrolling, hold 2 to erase
position, 3 all controllers, 4 to
erase all items
-
Exit delay 20x
x = 1 to 9 (x 10sec.) 30sec.
Entrance delay 21x
x = 1 to 9 (x 10sec.)
30sec.
Alarm duration 22x x = 1 to 8 (min.), for x=0 it
will be 10 sec., for x=9 15min.
4min.
Function of PgX output 23x x = 0 to 8 (0-Chime, 1-Fire,
2-Arm, 3-Panic, 4-Alarm,
5-Door, 6-Home, 7-NO AC,
8-Phone
Chime
Function of PgY output 24x x = 0 to 8 (0-Chime, 1-Fire,
2-Arm, 3-Panic, 4-Alarm,
5-Door, 6-Home, 7-NO AC,
8-Phone
Arm
Voice message & phone numbers: editable in the
user mode 25x
251 = YES 250 = NO
NO
Radio signal jamming regular testing 26x 261 = YES 260 = NO NO
Regular communication check enabled
27x
271 = YES 270 = NO NO
RESET enabled 28x
281 = YES 280 = NO
YES
Control panel teaching to a UC-2xx, subsystem,... 299 will send enrolling signal -
No code requested (effects F1, F2, F3, F4, F8 & F9) 30x 301 = YES 300 = NO YES
Partial (Home) arming enabled (F2) 31x
311 = YES 310 = NO
YES
Siren alarm enabled 32x
321 = YES 320 = NO
YES
Exit delay audible indication enabled 33x 331 = YES 330 = NO YES
Partial arming exit delay audible indication
34x
341 = YES 340 = NO NO
Entrance delay audible indication enabled 35x
351 = YES 350 = NO
YES
Arming & disarming chirp sound enabled 36x 361 = YES 360 = NO NO
Siren in Disarm & Partial arming enabled 37x 371 = YES 370 = NO YES
Wireless siren alarm enabled 38x
381 = YES 380 = NO YES
Indication of system problems when arming 39x
391 = YES 390 = NO
NO
Split control panel (A, B & C sections) 690x 6901 = YES 6900 = N0
NO
Addressing of wireless detectors to sections 61 nns
nn – zone n., s - section 1-10 A only when split
Addressing of user codes to sections 62 nns
nn – code n., s - section
all A
only when split
Addressing of wireless controllers to sections 63 nns
nn – controller n., s - section all A only when split
Automatic arming/disarming setting 64nahhm
m
n - 0-9, a -action #, hh -hours,
mm -min.
all off
New Service Code setting 5
nSC nSC
nSC = new Service Code
(must be entered twice)
6060
User Mode entering 6999 Switching to the User mode
-
Real time and date setting 4 hh mm DD MM YY 00 00 01 01 00
8.1. Testing of the system when the LED display displays „P“
In the programming mode (indicated by a „P“) no alarm can be triggered. The control panel will confirm receiving any
signal from an enrolled detector or another JA-60 wireless item. It will make a beep - press F to select the loudness of the
beep (0-I-II) and the LED display will show which signal was received. Some detectors (JA-60P, JA-60N etc.) have an
extra testing mode, which is usually activated for 5 minutes after the detector’s cover is attached (see manuals of the
particular detectors).
Just as in the programming mode, the signals from all enrolled items are confirmed in the user mode (confirmed by a
“U”). The user mode is accessible with the Master code and the supervisor of the system can use this mode to replace
batteries in items or for system testing. To open the user mode enter F 0 MC (= Master Code) when the control panel is
disarmed.