ISHIDA BC-4000TEC User Manual Download

Page: 94 / 128

Chapter 5 REGISTRATION MODE

RECEIVING FILES (P23-03)

[P23 Screen]

Make sure that “TCP/IP Mode” screen
(P23) appears on the display.

Otherwise, access this screen by referring
to Section 5.1: Registration Mode
Entry/Exit.

[Delete]

Press the [ENTER] key to access “Delete”
screen (P23-01).

[Receive]

Press the [

↓

] key twice to proceed to

“Receive” screen (P23-03).

[PLU File Receive]

Press the [ENTER] key to access “PLU
File Receive” screen (P23-03-01).

Press the [ENTER] key to receive the file.
Otherwise, move to the next step.

[Store File Receive]

Press the [

↓

] key to proceed to “Store File

Receive” screen (P23-03-02).

Press the [ENTER] key to receive the file.
Otherwise, move to the next step.

5-42

BC-4000TEC User’s Manual No. JBAW97EBC-4000TEC

Summary of Contents for BC-4000TEC

































































































































Search results

Summary of Contents for BC-4000TEC

Reviews:

Related manuals for BC-4000TEC

Brands by name

Popular brands

ISHIDA BC-4000TEC, User Manual

Search results

Summary of Contents for BC-4000TEC

Reviews:

Related manuals for BC-4000TEC

Brands by name

Popular brands