ISHIDA BC-4000TEC User Manual Download

Page: 76 / 128

Chapter 5 REGISTRATION MODE

[Erase Store]

Press [

↓

] key twice to access “Erase Store”

screen (P05-03).

[Store Delete]

Press [ENTER] key to access “Store
Delete” screen (P05-03-01).

Press [DELETE] key to delete the store.

Note: Press [ENTER] before [DELETE] to

return to P05-00 (Store Number)
screen without deleting store.

[DELETE]

[Return to P05-00]

A short beep will be heard and the screen
will automatically return to the P05-00
screen.

A short beep will be heard.

[Return to P01]

Press the [END] key to return to the P01
screen.

[Registration Mode Exit]

To exit Registration Mode, press the
[MODE] key.

The initial screen will appear.

5-24

BC-4000TEC User’s Manual No. JBAW97EBC-4000TEC

Summary of Contents for BC-4000TEC

































































































































Search results

Summary of Contents for BC-4000TEC

Reviews:

Related manuals for BC-4000TEC

Brands by name

Popular brands

ISHIDA BC-4000TEC, User Manual

Search results

Summary of Contents for BC-4000TEC

Reviews:

Related manuals for BC-4000TEC

Brands by name

Popular brands