ISHIDA BC-4000TEC User Manual Download

Page: 77 / 128

Chapter 5 REGISTRATION MODE

5.8 DATE/TIME (P06)

[P06 Screen]

Make sure that “Date/Time Mode” screen
(P06) appears on the display.

Otherwise, access this screen by referring to
Section 5.1: Registration Mode Entry/Exit.

[Date]

Press the [ENTER] key to access “Date”
screen (P06-01).

Key in a desired date (MMDDYYYY) and
press the [ENTER] key.

Date (MMDDYYYY)

[Time]

Press the [

↓

] key to proceed to “Time”

screen (P06-02).

Key in desired time (HHMMSS) and press
the [ENTER] key.

Time (HHMMSS)

[Julian Date]

Press the [

↓

] key to proceed to “Julian

Date” screen (P06-03).

Key in a desired Julian Date (XXXX) and
press the [ENTER] key.

Julian Date (XXXX)

BC-4000TEC User’s Manual No. JBAW97EBC-4000TEC

5-25

Summary of Contents for BC-4000TEC

































































































































Search results

Summary of Contents for BC-4000TEC

Reviews:

Related manuals for BC-4000TEC

Brands by name

Popular brands

ISHIDA BC-4000TEC, User Manual

Search results

Summary of Contents for BC-4000TEC

Reviews:

Related manuals for BC-4000TEC

Brands by name

Popular brands