ISHIDA BC-4000TEC User Manual Download

Page: 92 / 128

Chapter 5 REGISTRATION MODE

SENDING FILES (P23-02)

[P23 Screen]

Make sure that “TCP/IP Mode” screen
(P23) appears on the display.

Otherwise, access this screen by referring
to Section 5.1: Registration Mode
Entry/Exit.

[Delete]

Press the [ENTER] key to access “Delete”
screen (P23-01).

[Send]

Press the [

↓

] key to proceed to “Send”

screen (P23-02).

[PLU File Send]

Press the [ENTER] key to access “PLU
File Send” screen (P23-02-01).

Press the [ENTER] key to send the file.
Otherwise, move to the next step.

[Store File Send]

Press the [

↓

] key to proceed to “Store File

Send” screen (P23-02-02).

Press the [ENTER] key to send the file.
Otherwise, move to the next step.

5-40

BC-4000TEC User’s Manual No. JBAW97EBC-4000TEC

Summary of Contents for BC-4000TEC

































































































































Search results

Summary of Contents for BC-4000TEC

Reviews:

Related manuals for BC-4000TEC

Brands by name

Popular brands

ISHIDA BC-4000TEC, User Manual

Search results

Summary of Contents for BC-4000TEC

Reviews:

Related manuals for BC-4000TEC

Brands by name

Popular brands