ISHIDA BC-4000TEC User Manual Download

Page: 106 / 128

Chapter 5 REGISTRATION MODE

FILE DELETE (P29-02)

[P29 Screen]

Make sure that “Campaign Item” screen
(P29) appears on the display.

Otherwise, enter this screen by referring to
Section 5.1: Registration Mode Entry/Exit.

[Key In Group Code]

Press the [ENTER] key to enter “Key In
Campaign No.” screen (P29-00).

Key in a file number (1 to 20) and press the
[PLU] key.

File number

[P29-01 screen]

Press the [

↑

] key to proceed to “Process

Campaign Delete” screen (P29-02).

[Campaign Delete]

Press the [ENTER] key to move to
“Campaign Delete” screen (P29-03)..

[Executing Delete]

Press the [DELETE] key to execute deletion,
then, a buzzer will sound.

Note: When canceling the deletion, press the

[ENTER] key.

[Return to P01]

Press the [END] key to return to the P01
screen.

5-54

BC-4000TEC User’s Manual No. JBAW97EBC-4000TEC

Summary of Contents for BC-4000TEC

































































































































Search results

Summary of Contents for BC-4000TEC

Reviews:

Related manuals for BC-4000TEC

Brands by name

Popular brands

ISHIDA BC-4000TEC, User Manual

Search results

Summary of Contents for BC-4000TEC

Reviews:

Related manuals for BC-4000TEC

Brands by name

Popular brands