ISHIDA BC-4000TEC User Manual Download

Page: 59 / 128

Chapter 5 REGISTRATION MODE

[Pack Time Data]

Press the [

↓

] key to proceed to “Pack Time

Data” screen (P01-15).

Key in Pack Time (HHMM) and press the
[ENTER] key.

Pack time (HHMM)

[Sale By Time Flag]

Press the [

↓

] key to proceed to “Sale By

Time Flag” screen (P01-16).

Key in desired selection data (see below)
and press the [ENTER] key.

Selection data

0: Reference
1: Prohibition
2: Designated
3: Relative

Note: When “0” is set in Step 16 above, B04-04:

Sale By Time Flag in Setup Mode is
referred to.

Selection data

[Sale By Time Data]

Press the [

↓

] key to proceed to “Sale By

Time Data” screen (P01-17).

Key in Sale By Time (HHMM) and press the
[ENTER] key.

Expiry time (HHMM)

[Item Code]

Press the [

↓

] key to proceed to “Item Code”

screen (P01-18).

Key in a item code (8 digits) and press the
[ENTER] key.

Note: When a new PLU is programmed, the

barcode default is to be PLU number.

Item code

BC-4000TEC User’s Manual No. JBAW97EBC-4000TEC

5-7

Summary of Contents for BC-4000TEC

































































































































Search results

Summary of Contents for BC-4000TEC

Reviews:

Related manuals for BC-4000TEC

Brands by name

Popular brands

ISHIDA BC-4000TEC, User Manual

Search results

Summary of Contents for BC-4000TEC

Reviews:

Related manuals for BC-4000TEC

Brands by name

Popular brands