ISHIDA BC-4000TEC User Manual Download

Page: 86 / 128

Chapter 5 REGISTRATION MODE

DOWNLOADING DATA (P10-02) ** NOT AVAILABLE **

[P10 Screen]

Make sure that “RS232C Mode” screen
(P10) appears on the display.

Otherwise, enter this screen by referring to
Section 5.1: Registration Mode Entry/Exit.

[Data Upload]

Press the [ENTER] key to enter “Data
Upload” screen (P10-01).

[Data Download]

Press the [

↓

] key to proceed to “Data

Download” screen (P10-02).

To download all data, press the [ENTER]
key.

[Receiving]

While all data is being received,
“RECEIVING” screen is displayed.

Note: In order to exit receiving status, turn OFF

and ON the power.

[Return to P01]

Press the [END] key to return to the P01
screen.

[Registration Mode Exit]

To exit Registration Mode, press the
[MODE] key.

The initial screen will appear.

5-34

BC-4000TEC User’s Manual No. JBAW97EBC-4000TEC

Summary of Contents for BC-4000TEC

































































































































Search results

Summary of Contents for BC-4000TEC

Reviews:

Related manuals for BC-4000TEC

Brands by name

Popular brands

ISHIDA BC-4000TEC, User Manual

Search results

Summary of Contents for BC-4000TEC

Reviews:

Related manuals for BC-4000TEC

Brands by name

Popular brands