ISHIDA BC-4000TEC User Manual Download

Page: 28 / 128

Chapter 2 DAILY OPERATION

2.3 FIXED PRICE ITEMS

[Initial Display]

Press the [MODE] key.

Make sure that the initial display appears
and the ZERO indicator is lit.

Note: If the ZERO indicator is not lit, press the

[ZERO] key to turn on the indicator.

[PLU Call Up]

Key in a desired PLU number and press
the [PLU] key, or press a desired preset
PLU key.

Note: Refer to Step 2 of Section 2.2 for PLU call

up procedures.

Example: Fixed price item PLU “1”

[Automatic Label Issue]

For a fixed price item and when the machine
is in AUTO mode, key in the desired number
of labels to be issued and press the [PRINT]
key.

Note 1: If the number of labels to be issued has

not been keyed in, labels are issue
continuously. To stop label issue, press
the [PRINT] key again.

Note2: To eliminate the AUTO indicator, press

the [PREPACK] key.

Example: 8 labels

[Manual Label Issue]

When the machine is in MANUAL mode,
press the [PRINT] key to issue a label.

Note: In MANUAL mode, only one label is

issued.

2-8

BC-4000TEC User’s Manual No. JBAW97EBC-4000TEC

Summary of Contents for BC-4000TEC

































































































































Search results

Summary of Contents for BC-4000TEC

Reviews:

Related manuals for BC-4000TEC

Brands by name

Popular brands

ISHIDA BC-4000TEC, User Manual

Search results

Summary of Contents for BC-4000TEC

Reviews:

Related manuals for BC-4000TEC

Brands by name

Popular brands