ISHIDA BC-4000TEC User Manual Download

Page: 68 / 128

Chapter 5 REGISTRATION MODE

5.3 COMMODITY NAME (P02)

[P02 Screen]

Make sure that “Commodity Name” screen
(P02) appears on the display.

Otherwise, access this screen by referring to
Section 5.1: Registration Mode Entry/Exit.

[Key In PLU No.]

Press the [ENTER] key to access “Key In
PLU No.” screen (P02-00).

Key in a PLU number (8 digits) and press the
[PLU] key to call up a desired PLU

PLU number

[Commodity Name Edit]

Press the [ENTER] key to enter Edit Mode
screen (P02-01).

Refer to Chapter 6 for editing a text.

[Return to P01]

Press the [END] key to return to P01 screen.

[Registration Mode Exit]

To exit Registration Mode, press the
[MODE] key.

The initial screen will appear.

5-16

BC-4000TEC User’s Manual No. JBAW97EBC-4000TEC

Summary of Contents for BC-4000TEC

































































































































Search results

Summary of Contents for BC-4000TEC

Reviews:

Related manuals for BC-4000TEC

Brands by name

Popular brands

ISHIDA BC-4000TEC, User Manual

Search results

Summary of Contents for BC-4000TEC

Reviews:

Related manuals for BC-4000TEC

Brands by name

Popular brands