ISHIDA BC-4000TEC User Manual Download

Page: 84 / 128

Chapter 5 REGISTRATION MODE

5.12 RS232C MODE (P10)

RS232C MODE NOT APPLICABLE TO THE BC-4000TEC SCALE

LOADING DATA (P10-01) ** NOT AVAILABLE **

[P10 Screen]

Make sure that “RS232C Mode” screen
(P10) appears on the display.

Otherwise, enter this screen by referring to
Section 5.1: Registration Mode Entry/Exit.

[Data Upload]

Press the [ENTER] key to enter “Data
Upload” screen (P10-01).

[All Data]

Press the [ENTER] key to enter “All Data”
screen (P10-01-01).

To upload all data, press the [ENTER] key.
Otherwise, move to the next step.

[Store Data]

Press the [

↓

] key to proceed to “Store

Data” screen (P10-01-02).

To upload store data, press the [ENTER]
key. Otherwise, move to the next step.

5-32

BC-4000TEC User’s Manual No. JBAW97EBC-4000TEC

Summary of Contents for BC-4000TEC

































































































































Search results

Summary of Contents for BC-4000TEC

Reviews:

Related manuals for BC-4000TEC

Brands by name

Popular brands

ISHIDA BC-4000TEC, User Manual

Search results

Summary of Contents for BC-4000TEC

Reviews:

Related manuals for BC-4000TEC

Brands by name

Popular brands