ISHIDA BC-4000TEC User Manual Download

Page: 61 / 128

Chapter 5 REGISTRATION MODE

[POS Flag]

Press the [

↓

] key to proceed to “POS Flag”

screen (P01-21).

Key in POS Flag (Barcode prefix) (2 digits)
and press the [ENTER] key.

Note: When “0” is set, the value of B02-01: POS

Flag 8/13 is used.

POS flag

[POS Code]

Press the [

↓

] key to proceed to “POS

Code” screen (P01-22).

Key in a POS code (10 digits) and press the
[ENTER] key.

Note: When “0” is set, the value of P01-18: Item

Code is used.

POS code

[[Open Price]

Press the [

↓

] key to proceed to “Open

Price” screen (P01-23).

Key in desired selection data (see below)
and press the [ENTER] key.

Selection data

0: Reference
1: Price change prohibited
2: Price change allowed

Selection data

[Message 1]

Press the [

↓

] key to proceed to “Message

1” screen (P01-24).

Key in a Message 1 number (8 digits) and
press the [ENTER] key.

Note1: “0” means “Not specified”.

Note2: Message 1 must be programmed at P07.

Message 1 in Registration Menu.

Message 1 number

BC-4000TEC User’s Manual No. JBAW97EBC-4000TEC

5-9

Summary of Contents for BC-4000TEC

































































































































Search results

Summary of Contents for BC-4000TEC

Reviews:

Related manuals for BC-4000TEC

Brands by name

Popular brands

ISHIDA BC-4000TEC, User Manual

Search results

Summary of Contents for BC-4000TEC

Reviews:

Related manuals for BC-4000TEC

Brands by name

Popular brands