Ip.Access nano3G AP Installation Manual Download | Manualshive

Page: 76 / 89

background image

nano3G AP Installation Manual

Troubleshooting

N3G_INST_300 v14.0 for N3G_2.85 © ip.access Limited 2012

Page 70

8.1.2

nano3G S8 AP LEDs

The following table shows the meaning of the status LEDs under normal and fault
conditions.

Power

Off

The AP is not switched on.

Green

The AP is powered up normally.

Flashing green

Self-test is running.

Red

There is a fault with the AP.

Ethernet
Link

Amber

This is on to show the link is active, or flashes when there is network
activity.

Ethernet
Speed

Green

Shows the network speed. On for 100Mbps or off for 10Mbps.

Power

Off

The nano3G AP is not switched on.

Green

The nano3G AP is powered up normally.

Flashing green

Self-test is running.

Red

There is a fault with the nano3G AP.

Network

Off

Unable to detect a network. This is usually because there is no
network cable connected, or there is no network connection at the
other end of the cable (for example, the router or broadband modem
may have failed).

Green

The 100Mbps connection is OK.

Flashing green

Indicates activity on the network at 100Mbps speed (that is, the
nano3G AP is sending and/or receiving data across the LAN).

Amber

The 10Mbps connection is OK.

Flashing amber

Indicates activity on the network at 10Mbps speed (that is, the
nano3G AP is sending and/or receiving data across the LAN).

Service

Off

The nano3G AP is not provisioned, it has no IP address. This may be
a temporary condition when the AP is switched on for the first time, or
after factory reset.

Green

The nano3G AP is provisioned and unlocked, it is connected to the
AP and is providing service.

Flashing green
(evenly, slowly)

The nano3G AP is provisioned but has lost connection to the AC, for
example because the AC is not available or there is a DNS problem.

Flashing green
(evenly, fast)

The nano3G AP has been reinitialized (the reset button was pressed
but for less than 5 seconds).

Off, with a short
green blink every
3 seconds

The nano3G AP is administratively Locked.

Off, with short
green blinks on

Factory reset is in progress in the nano3G AP (the reset button was
pressed for more than 5 seconds).

On, with short
green blinks off

Software download is in progress to the nano3G AP.

«
...
74
75
76
77
78
...
»

Summary of Contents for nano3G AP


























































































Reviews:

No comments

Related manuals for nano3G AP

Brand: Tenda Pages: 34

Brand: SMC Networks Pages: 2

3CRWER101U-75 - Wireless 11g Cable/DSL...

Brand: 3Com Pages: 76

Nfiniti Airstation WHR-G300N

Brand: Buffalo Tech Pages: 48

Brand: D-Link Pages: 18

Brand: D-Link Pages: 3

Brand: D-Link Pages: 3

Brand: D-Link Pages: 49

Brand: D-Link Pages: 68

Brand: D-Link Pages: 46

Brand: D-Link Pages: 64

Brand: D-Link Pages: 12

Brand: D-Link Pages: 75

Brand: D-Link Pages: 36

Brand: D-Link Pages: 92

Brand: D-Link Pages: 110

Brand: D-Link Pages: 154

Brand: D-Link Pages: 36

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands