Ip.Access nano3G AP Installation Manual Download

Page: 55 / 89

nano3G AP Installation Manual

nano3G AP Hardware Installation

N3G_INST_300 v14.0 for N3G_2.85 © ip.access Limited 2012

Page 49

nano3G AP Hardware Installation

This section documents the procedures for installing the nano3G AP hardware and physical
connections.

The following hardware variants are described:

•

6.2 nano3G S8 AP Hardware Installation

•

6.3 nano3G E8 AP and E16 AP Hardware Installation

Note:

If possible, the engineer should stay on site until the AP is brought into service, ready to
make test calls to verify the AP has been configured correctly from the NOS.

Note:

For residential deployments where an AP is installed by an end-user following an easy
setup guide, ignore all of section 6.

6.1

Warnings and Regulatory Information

For all warnings and regulatory information, see section 9.

Summary of Contents for nano3G AP


























































































Search results

Summary of Contents for nano3G AP

Reviews:

Related manuals for nano3G AP

Brands by name

Popular brands

Ip.Access nano3G AP, Installation Manual

Search results

Summary of Contents for nano3G AP

Reviews:

Related manuals for nano3G AP

Brands by name

Popular brands