Ip.Access nano3G AP Installation Manual Download

Page: 21 / 89

nano3G AP Installation Manual

Installation Overview and Requirements

N3G_INST_300 v14.0 for N3G_2.85 © ip.access Limited 2012

Page 15

2.3.3

nano3G S8 AP IP Bandwidth Requirements

At maximum capacity, a nano3G S8 AP will require:

• Downlink: 17Mbps

• Uplink: 1.8Mbps

This will deliver up to 8 voice calls and HSDPA services up to 14.4 Mbps.

Note:

If the available bandwidth on site does not meet the requirements see the Troubleshooting
section N User Configuration8.

2.3.4

nano3G S8 AP Sundry Installation Equipment

To mount the POE splitter or the nano3G S8 AP onto the wall:

• 2 self tapping pan head screws, size No. 6 (approx 3.5mm (0.14in) in diameter)

• Wall plugs if required

• Suitable drills and screwdriver

Note:

If the available bandwidth on site does not meet the requirements see the Troubleshooting
section N User Configuration8.

Summary of Contents for nano3G AP


























































































Search results

Summary of Contents for nano3G AP

Reviews:

Related manuals for nano3G AP

Brands by name

Popular brands

Ip.Access nano3G AP, Installation Manual

Search results

Summary of Contents for nano3G AP

Reviews:

Related manuals for nano3G AP

Brands by name

Popular brands