Intel SRCU32 - RAID Controller User Manual Download Page 47 | Manualshive

Page: 47 / 182

background image

47

3 Installing Microsoft Windows NT or

Windows 2000

This section covers installation issues related to the Microsoft Windows NT and Windows 2000
operating systems. For a successful installation, study the Windows NT/2000 system manuals
thoroughly. The required Intel RAID Controller SRCU32 disks can be created from the Intel RAID
Controller SRCU32 system CD-ROM.

Operating System Installation Procedures

✏

✏

✏

✏

NOTE

Begin the installation process in this chapter if you are installing the OS and Intel RAID Controller
SRCU32 or upgrading from the Windows NT OS (the OS is currently installed on a compatible
Intel RAID Controller SRCU32) to Windows 2000.

Your installation falls into one of two categories:

•

Install the OS on either a RAID volume or single disk that is attached to and configured on the
Intel RAID Controller SRCU32 that you are installing,
OR

•

Install the OS on either an IDE hard drive or a SCSI hard drive that is not attached to the Intel
RAID Controller SRCU32 that you are installing

Pre-Installation Requirements Checklist

This section identifies the minimum hardware and software required to successfully install the Intel
RAID Controller SRCU32 and the accompanying software suite.

Minimum Hardware Requirements

✏

NOTE

The Intel RAID Controller SRCU32 will work in a 32-bit, 33 or 64 MHz PCI slot; however, a 64-bit
66 MHz slot is recommended for maximum performance.

•

Computer with CD-ROM drive (not attached to the Intel RAID Controller SRCU32).
Computer must be on the supported hardware list.

•

One available PCI slot.

See note above.

•

PCI 2.2 compliant System BIOS.

•

SCSI hard drive(s) (the minimum required to meet the desired RAID level).

«
...
45
46
47
48
49
...
»

Summary of Contents for SRCU32 - RAID Controller























































































































































































Reviews:

No comments

Related manuals for SRCU32 - RAID Controller

Brand: Ebyte Pages: 8

Brand: Samsung Pages: 65

Brand: Harmonic Pages: 56

Brand: SIIG Pages: 12

LoadMaster 1500

Brand: KEMP Technologies Pages: 71

Brand: Dialogic Pages: 2

Brand: Black Box Pages: 37

IntroSpect Analyzer 2 Series

Brand: Aruba Pages: 5

Brand: DigiTech Pages: 6

Brand: ekwb Pages: 11

Open Standard Module RPX30 EVA-MI V1

Brand: iesy Pages: 9

Brand: IEI Technology Pages: 136

ARC-12x4 Series

Brand: Areca Pages: 2

Brand: Holtek Pages: 280

Brand: LevelOne Pages: 142

NetStructure ZT 5085

Brand: Intel Pages: 106

Brand: M86 Security Pages: 512

EK-TIM Indigo Extreme

Brand: ekwb Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands