Intel SRCU32 - RAID Controller User Manual Download Page 77 | Manualshive

Page: 77 / 182

background image

77

7 Storage

Console

Storage Console (StorCon) is a helpful and flexible setup and diagnosis tool for the configuration,
monitoring, maintenance and tuning of mass storage subsystems that are based on one or more Intel
RAID Controller SRCU32. Unlike Storage Console Plus (), a GUI-style application for
Windows 9x/NT/2000, StorCon’s user interface is character-oriented and available for all operating
systems. Information on is found in Chapter 8, Storage Console Plus. StorCon is also
part of the Intel RAID Controller SRCU32’s Flash-RAM and can be loaded at system boot level by
pressing <Ctrl> + <G>.

✏

NOTE

Some features are only available from the BIOS/Flash-RAM version of the StorCon to prevent users
from experiencing unrecoverable events.

StorCon Features

•

Diagnosis and configuration functions

•

Online capacity expansion of disk arrays

•

Host drives which can be setup and configured under normal operation

•

Monitoring functions which indicate the performance of the various components, cache
statistics

•

Enhanced repair functions for disk arrays with failed drives

StorCon Is

•

Available as both an executable program under various operating systems, and a rom-resident
program loadable with <Ctrl> + <G> at system boot level (for example, without an operating
system)

•

Available for NetWare 5.1, Windows NT, Windows 2000, Linux, and SCO UnixWare

•

Loadable locally (on the server) or remotely from an authorized workstation (support of various
protocols)

«
...
75
76
77
78
79
...
»

Summary of Contents for SRCU32 - RAID Controller























































































































































































Reviews:

No comments

Related manuals for SRCU32 - RAID Controller

Brand: NAIM Pages: 2

SCSI PC Card REX-9530V

Brand: Ratoc Systems Pages: 30

PG-FLEX RT FRL-752

Brand: PairGain Pages: 6

Brand: Qlogic Pages: 8

Brand: ZALMAN Pages: 5

RouterBOARD 411R

Brand: 4gon Pages: 2

Brand: Omron Pages: 13

Brand: Aaeon Pages: 72

Brand: Intel Pages: 958

Brand: PairGain Pages: 80

Brand: Air Live Pages: 2

Brand: Matrix Switch Corporation Pages: 48

Brand: PairGain Pages: 48

Brand: FDI Pages: 15

Brand: NEC Pages: 26

Brand: protech Pages: 84

Brand: Matrix Switch Corporation Pages: 48

Brand: ST Pages: 64

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands