Intel SRCU32 - RAID Controller User Manual Download Page 21 | Manualshive

Page: 21 / 182

background image

21

2 Getting

Started

What is the Intel RAID Controller SRCU32 Firmware?

We refer to firmware as the operating system that controls the Intel RAID Controller SRCU32 with
all of its functions and capabilities. The firmware exclusively runs on the Intel RAID Controller
SRCU32 and is stored in the Flash-RAM on the Intel RAID Controller SRCU32 PCB. The
controlling function is entirely independent of the PCI computer and the host operating system, and
does not drain computing power or time from the PCI computer. According to the system
requirements needed, the Intel RAID Controller SRCU32 is available with two firmware variants.
The firmware is either already installed on the controller upon delivery, or can be added as an
upgrade.

Unlike pure software solutions, for example, for Windows NT, the Intel RAID Controller SRCU32
is a pure hardware RAID solution. All Intel RAID Controllers are equipped with hardware that is
well suited for disk arrays. The Intel RAID Controller SRCU32 firmware uses this hardware with
efficiency and therefore allows you to configure disk arrays that do not load the host computer
(whereas all software-based RAID solutions more or less reduce the overall performance of the host
computer).

The basic concept of the Intel RAID Controller SRCU32 firmware is strictly modular, and
consequently, in its functioning it appears to the user as a unit construction system.

Standard Firmware

In addition to simple controlling functions regarding SCSI hard drives or removable hard drives,
this version of firmware supports disk chaining and array drive configuration (data striping
(RAID 0) and disk mirroring or duplexing (RAID 1)).

WARNING

Disk Chaining does not offer any form of data protection and can result in loss of data. It is
therefore recommended not to use logical drives of the type chain as components of array drives.

«
...
19
20
21
22
23
...
»

Summary of Contents for SRCU32 - RAID Controller























































































































































































Reviews:

No comments

Related manuals for SRCU32 - RAID Controller

Brand: Parker Pages: 344

Brand: 3xLogic Pages: 2

Brand: Alcad Pages: 6

Brand: VMIC Pages: 126

Brand: SIIG Pages: 12

eXtremeRAID 1100

Brand: Mylex Pages: 74

Brand: Fracarro Pages: 12

MultiConnect SE MTS2EA

Brand: Multitech Pages: 2

Brand: Kaptia Pages: 14

CNPS11X Extreme

Brand: ZALMAN Pages: 12

Brand: CNC4PC Pages: 11

Brand: AXIOMTEK Pages: 2

WAFER-EHL Series

Brand: IEI Technology Pages: 142

Brand: RadioSPECTRAL Pages: 2

Brand: ZALMAN Pages: 9

ULTRIX-FM-NS-1RU

Brand: Ross Pages: 5

Brand: ADLINK Technology Pages: 95

Brand: ICP DAS USA Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands