Intel SRCU32 - RAID Controller User Manual Download Page 71 | Manualshive

Page: 71 / 182

background image

71

6 Installing

UnixWare

This section discusses installation issues related to the UnixWare operating systems
(UnixWare 7.1.1). For a successful installation, study the SCO UNIX system manuals thoroughly.
The required Intel RAID Controller SRCU32 disks can be created from the Intel RAID Controller
SRCU32 system CD-ROM.

General Installation Notes

This section identifies the minimum hardware and software required to successfully install the Intel
RAID Controller SRCU32 the accompanying RAID Software Suite.

Minimum Hardware Requirements

✏

NOTE

The Intel RAID Controller SRCU32 will work in a 32-bit, 33 or 64 MHz PCI slot; however, a 64-bit
66 MHz slot is recommended for maximum performance.

•

Computer with CD-ROM drive (not attached to the Intel RAID Controller SRCU32).
Computer must be on the supported hardware list (for example, Intel SCB2 server board).

•

One available PCI slot

. See note above.

•

PCI 2.2 compliant System BIOS.

•

SCSI hard drive(s) (the minimum required to meet the desired RAID level).

Minimum Software Requirements

•

RAID Software Suite CD-ROM

•

20 MB of hard drive space

•

RAID Driver Installation Diskette for UnixWare

•

SCO UnixWare 7.1 OS software

«
...
69
70
71
72
73
...
»

Summary of Contents for SRCU32 - RAID Controller























































































































































































Reviews:

No comments

Related manuals for SRCU32 - RAID Controller

Brand: NAIM Pages: 2

Brand: Idis Pages: 123

Brand: Idis Pages: 29

Brand: Idis Pages: 28

DirectIP DR-1304P

Brand: Idis Pages: 82

INTERNET PRIVACY PROTECTION

Brand: AlphaShield Pages: 49

Brand: 3Com Pages: 18

Brand: Supermicro Pages: 24

Brand: Zonet Pages: 2

Anybus Communicator ABC4021

Brand: HMS Networks Pages: 60

Brand: Hama Pages: 6

kontron KBox E-420-R1K/V1K

Brand: S&T Pages: 82

PSoC 4 S Series

Brand: Cypress Pages: 4

Brand: Intellinet Pages: 2

Brand: Digital Equipment Pages: 90

Modular Fast Fiber Switch Converter MT-RJ

Brand: Lindy Pages: 3

Brand: LevelOne Pages: 4

SNMP-1000-E2B1E

Brand: Advantech Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands