Intel SRCU32 - RAID Controller User Manual Download Page 125

Page: 125 / 182

Storage Console Plus

125

The Status Bar

The status bar at the bottom of the main window displays status information on the icon or the
menu option the mouse pointer is currently placed on. The status bar can be displayed or hidden by
selecting “Status Bar” from the View menu.

Figure 68. Status Bar

Window Menu Commands

These commands allow you to arrange the windows in the application window or to
activate an open window.

Figure 69. Window Menu

Help Menu Commands

Use the Help menu to access online help.

Figure 70. Help Menu

Summary of Contents for SRCU32 - RAID Controller























































































































































































Search results

Summary of Contents for SRCU32 - RAID Controller

Reviews:

Related manuals for SRCU32 - RAID Controller

Brands by name

Popular brands

Intel SRCU32 - RAID Controller, User Manual

Search results

Summary of Contents for SRCU32 - RAID Controller

Reviews:

Related manuals for SRCU32 - RAID Controller

Brands by name

Popular brands